A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in figure. If the volumetric flow rate (taking unit depth) of an incompressible flow through the main channel is 0.9 m³/s and the velocity in the sub-channel of width 200 mm is 3 m/s, the velocity in the sub-channel of width 300 mm is _m/s Assume both inlet and otlet to be at the same elevation. Width = 300 mm Width = 450 mm Flow rate= 0.9m³/s Width = 200 mm Velocity = 3m/s

A channel of width 450 mm branches into two sub-channels having width 300 mm and 200 mm as shown in figure. If the volumetric flow rate (taking unit depth) of an incompressible flow through the main channel is 0.9 m³/s and the velocity in the sub-channel of width 200 mm is 3 m/s, the velocity in the sub-channel of width 300 mm is _m/s Assume both inlet and otlet to be at the same elevation. Width = 300 mm Width = 450 mm Flow rate= 0.9m³/s Width = 200 mm Velocity = 3m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 7 - 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir Cif the inflow to reservoir A is 515 Lit/sec. L El. ? C El. 90 m El. 90 m D 300m - 450 mm t= 0.03 El. 80 m 600m - 600 mm t-0.025 300m - 450 mm f0.03 900m- 450 mm 600m - 450 mm Fx 0.03
Situation 1: For the pipe network shown, the flow of water from the reservoir A to the junction is 0.035 cu.m.per second. Pipe 1: L = 300 m, D 202.70 mm, f = 0.015 Pipe 4: L = 300 m, D = 381 mm, f 0.015 Pipe 5: L = 450 m, D 303.20 mm, f 0.015 %3D Pipe 2: L = 150 m, D 202.70 mm, f 0.015 Pipe 3: L 75 m, D 202.70 mm, f 0.015 A B Q, = 0.035cumecs 4. Determine the flow in the upper branch Q2. 5. Determine the flow in the lower branch Q3. 6. Determine the flow in the lower branch Q4. 7. Determine the total head loss between the inlet A and the outlet B.
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m³/s. Pipe Length Diameter Friction Factor 400 mm 1,800 mm 1,500 mm 2,000 mm 1 0.020 X A 2 в У 2 350 mm 0.018 300 mm 0.022 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
Situation 2 Pipelines 1,2, and 3 are connected parallel to each other. The three pipes carry a combined discharge of 0.86 m/s. 1 Pipe Length Diameter Friction Factor 1,800 mm 1,500 mm 2,000 mm 0.020 0.018 0.022 400 mm A 2 в у 350 mm 3 300 mm 3 4. Determine the flow rate through pipeline 1 (Q1) in m3/s. 5. Determine the flow rate through pipeline 2 (Q2) in m3/s 6. Determine the flow rate through pipeline 3 (Q3) in m3/s
Problem 7- 64 Determine the flow in each pipe in the figure shown and the elevation of reservoir Cif the inflow to reservoir A is 515 Lit/sec. El. ? C El. 90 m El, 90 m B D. 300m - 450 mm t=0.03 El. 80 m 600m - 600 mm f-0.025 300m- 450 mem f0.03 900m- 450 mm 8. 600m - 450 mm 0.03
Given is the flow of a channel of large width b under asluice gate, as in Fig.. Assuming frictionless steadyflow with negligible upstream kinetic energy, derive a formulafor the dimensionless flow ratio Q2/(y 31b2g) as a functionof the ratio y2/y1. Show by differentiation that themaximum flow rate occurs at y2 = 2y1/3.
If u = xy + λy³x. v = -0.5y² + 6x³z and w = 5y²x - y³z + x, then for a steady and incompressible flow, value of λ will be
A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13 m³.sec¹, velocity when the depth is one quarter of the diameter is 0.6 m.sec¹¹. Assume the flow is uniform and determine the diameter and the slope of the pipe if you know that Chezy's coefficient is 58 mº.5 sec¹? Answer// D= 460 mm; S= 0.00158
The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and discharge Q1 = 50 ft2/s. Determine the following: (a) head loss (ft) in pipe 1, h1, (b) the elevation (el D') of the imaginary water surface at the junction, (c) the head loss (ft) in pipe 2, hL2, (d) the flow rate (ft³/s) in pipe 2, Q2. (e) the flow rate (ft/s) in pipe 3, Q3. (f) the head loss (ft) in pipe 3, hL3, (g) the elevation of the surface of reservoir C, El C. pipe L (ft) d (in) 1 5000 36 0.0157 2 1500 24 0.0162 3 4000 18 0.0177 A B D
A pipe line 60 cm diameter bifurcates at a Y- junction into two branches 40 cm and 30 cm in diameter. If the rate of flow in the main pipe is 1.5 m³/s and mean velocity of flow in 30 cm diameter pipe is 7.5 m/s. Determine the rate of flow in the 40 cm diameter pipe.
10. Determine the flow in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 lit/sec. El. 7 B. 90 m E. 90 m B. D. 300m-450 mm El. 80 m 600m-600 mm f 0.025 300m-450m f0.03 600m 450 mm
Specific energyA horizontal rectangular channel is 12 feet wide and carries a flow rate of 60 cfs. A hump that is 0.5 feet high is placed in the flow path. a. If the normal depth of flow is 1.5 feet, what is the depth of flow over the hump? b. If the normal depth of flow is 0.5 feet, what is the depth of flow over the hump?