The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the cross section shown (assume a=32 mm, b₁-65 mm, tw-tf-7 mm, d=89 mm), determine: (a) the shear stress T at point H, which is located 32 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a H Answers: (a) TH = i MPa. (b) Tmax y bf = V d

The internal shear force V at a certain section of an aluminum beam is 8.5 kN. If the beam has the cross section shown (assume a=32 mm, b₁-65 mm, tw-tf-7 mm, d=89 mm), determine: (a) the shear stress T at point H, which is located 32 mm above the bottom surface of the tee shape. (b) the maximum horizontal shear stress Tmax in the tee shape. a H Answers: (a) TH = i MPa. (b) Tmax y bf = V d

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum shearing stress developed in each segment. For bronze, G = 36 GPa; aluminum, G = 27 GPa, and for steel, G = 87 GPa. Tc = 280 N.m T₂ = 720 N.m C Aluminum D A Bronze Steel 25 mm 25 mm + 50 mm 2 m 2 m 2.5 m TA
- Determine the moment of intertia about the centroidal x-acid (in mm^4) - Determine the centroid location of the cross-section from the bottom fiber of the section (in mm) - Determine the bending stress at point H. Include a negative sign if compression. (in MPa.) - Determine the section modulus in reference to the bottom fiber (in mm^3) - Determine the maximum bending stress produced in the cross sectio. Include a negative sign if compression. (in MPa.)
Required information The cantilevered bar in the figure is made from a ductile material and is statically loaded with Fy= 380 Ibf and Fy = F7= 0. The diameter Dis 3 in and the height h is 3.5 in. Lengths AB and BC are 15 in. and 5 in., respectively. For the critical stress element, determine the principal stresses and the maximum shear stress. The principal stresses are o = 2488.69 psi and o2 = - 51.61 8 psi. The maximum shear stress is 1271 psi.
1. For the W 21x 62 steel beam below determine the actual value of om in the beam and the maximum value of the principal stress omax at the junction of the flange and the web. 20 kips 20 kips A B 10 ft 2 kips/ft 30 ft- C 10 ft D
Q.3) A simply supported wide-flange (see figure below) beam of span length L carries a vertical concentrated load P acting through the centroid C at the midpoint of the span. The beam is attached to supports inclined at an angle a to the horizontal. Determine the orientation of the neutral axis and calculate the maximum stresses at the outside corners of the cross section (points A, B, D, and E) due to applied load P. Data for the beam are as follows: W 10 x 30 section, L = 8.5 ft., P = 5 kips, and a = 26.57 degrees. 2. E α
Three plates are welded together to form the section shown. Dimensions of the cross section are b = 4.7 in., d = 14.1 in., a = 3.7 in., and t= 0.8 in. For a vertical shear force of V = 46 kips, determine the shear flow through the welded surface at B. d В b. Answer: kip/in.
Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z + 23e3. Assuming stress-strain relation: S = aE, where a is a constant, total force on the base of the cylinder with normal -e3 is f = -1.5anR2 He3 total force on the base of the cylinder with normal - ez is f = 1.5aπR²e3 total force on the base of the cylinder with normal - ez is f = 1.5an R²Hez total force on the base of the cylinder with normal - ez is f = -1.5anR²e3
please help need fast
Complete answer
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 69 mm and G = 33.49 GPa. For the steel segment BC, the diameter is 49 mm and G = 83.14 GPa. Given that a = 2 m and b = 1.4 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 63.68 MPa in the bronze and 90.99 MPa in the steel. Round off the final answer to two decimal places.
The internal shear force V at a certain section of an aluminum beam is 10.2 kN. If the beam has the cross section shown: a = 30mm, bf = 69mm, tw = tf = 4mm, d=72 mm, determine:(a) the shear stress Th at point H, which is located 30 mm above the bottom surface of the tee shape(b) the maximum horizontal shear stress Tmax in the tee shape
0.13