-) The gate shown below rests on a Sinooth floor at A and is hinged at B. Neglecting its weight, determine the vertical force P (in KN) required to open it when: (2.a) the gate is rectangular 2 m wide into the screen and h₁=h₂=0.6 m and s₁=S₂=1.0. (2.b) the gate is rectangular 2 m wide into the an h-06 h 06m -0

-) The gate shown below rests on a Sinooth floor at A and is hinged at B. Neglecting its weight, determine the vertical force P (in KN) required to open it when: (2.a) the gate is rectangular 2 m wide into the screen and h₁=h₂=0.6 m and s₁=S₂=1.0. (2.b) the gate is rectangular 2 m wide into the an h-06 h 06m -0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The gate AB is 8 m wide. Determine the horizontal and vertical components of force acting on the pin at B and the vertical reaction at the smooth support A; ρw = 1.0 Mg/m3.
The steel (Est = 200 GPa) shaft shown in composed of two hollow pipes AB and BC. The cross- sectional area of pipe AB is AAB= 790 mm2, and the cross-sectional area of pipe BC is ABC = 350 mm2. Determine the magnitude of the force P, applied at C as shown, required to close the %3D 0.15mm gap between the wall and C. Express your answer in kN to the nearest 100 N. -600 mm - 600 mm -0.15 mm P [A 50 mm B 25 mm
Q2. The force F acts on the end of the pipe at B. Determine (a) the moment of this force about point A (b) the magnitude and direction of a horizontal force, applied at C, which produces the same moment. Given: Rana F = 70 N a = 0.9 m b = 0.3 m c = 0.7 m F e = 60 deg
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 0=15⁰ a=3m b=3m c= 5m 5 panels@(a)m each F D E b G B Ө 0 P b b C Zoom image Compute the force induced in member DB. C P
4. I The gate shown in the figure below is a quarter circle and hinged at point H. Determine the horizontal force per unit width of the gate, P, required to hold the gate in place. Neglect the friction at the hinge and the weight of the gate. 6 ft Water Gate Hinge
Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the 3/4 in diameter pin is in double shear. ANS: P = 19770 lb-f A 10 in. B 30° P 12 in. C
Calculate the force P, that will hold the gate in, equilibrium. The bold yellow line is the whole gate. Width= 1m
P kN В W kN/m 12 m A 5 m 5 m Draw the schematic / blown-up diagram of the frame showing the member end forces. Assume P = 26 and w = 38. What is the constant axial force in member AB?
Q2/| Find the force P that is applied to keep the 3-m-wide gate in the position shown in the Figure below. If r-2 m. provide the value of P in (N). 60 cm P Quarter circle radius =r Water Hinge
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in is subjected to an axial force of P- 850 lb, a horizontal force of P, = 1560 lb, and a concentrated torque of T= 2940 Ib-in. acting in the directions shown. Assume a = 49 in. Section properties for the pipe are A = 2.2514 in. J= 8.199 in.", and I,= 1, = 4.0995 in. betermine the normal and shear stresses at point K, and show these stresses on a stress element T. Answer: Oy = psi Txy psi %3D
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
of tion Given the horizontal beam AB with two supports Pin A and Roller B. The system is subjected to external loads as shown in the following figure. A 6 3 4 5 1 3 KN/m 2 m a) The force due to distributed load w is KN located b) The resultant force of the equivalent system is located c) The vertical support reactions at pin A is 64 57 0.66 1.33 2 0.333 1.666 2.666 3.333 5.5 1.5 2.5 3.5 2 m 0.5 1.5 2.5 3.5 4KN.m B m measured from A. KN and at roller B is m measured from A. KN.