A beam is loaded and supported as shown.(a) Use the double-integration method to determine the reactions at supports A and C.(b) Draw the shear-force and bending-moment diagrams for the beam.Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam.%3DA-L/2-Part 1Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine anexpression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m.M(x)AAnswer:M(x) -kN-m +mA,eTextbook and Media

Answered: Image /qna-images/answer/545fb793-728a-48f7-9a2d-7192836a2089.jpg

A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D L/2

A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D L/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN.b. Moment Reaction at C in kN-m.c. Deflection at point B in mm.d. Maximum deflection on the beam in m Valuea = 4.8b = 28c = 11 Thank you very much!
For the beam shown, how does the shear change as you move from A to B? L- Select the correct response: There is not enough information to tell. It stays constant. It decreases linearly. It increases linearly
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m Figure 1: Overhang beam Find the equation of the elastic curve for the segment AB. L C - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
%3D The truss structure (all members have the same area) carry the loading shown (P = 150 kN) Determine the minimum thickness t (in mm) of the steel member considering allowable vertical displacement of C to be 12mm. Use E=200 GPa. Use Virtual Work Method to solve the problem. t E D = 200mm 3m C PV 4m 4m B
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m H Figure 1: Overhang beam L C Find the maximum absolute value of the deflection between the supports A and B - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
.. The continuous beam is loaded as shown in the figure. A is a fixed support, while B and C are roller. Assume that supports do notsettle, and El is constant. Using the consistent deformation method determine the following: a. Reactions at the supports. b. Sketch the shear and moment diagram of the beam. c. Determine the value and location of maximum shear and bending moment of the beam. A Sm 50 kN 5m 15 kN/m B 10m 60 kN Im D
No.2 For the beam shown, determine the reactions at the supports and the defection at E. Assume EI is constant. Use (a) Double Integration Method, (b) Moment Area Method, (c) Superposition Method A 75 kN DI | E 0.9 m 40 kN/m 2.4 m- -0.3 m -3.6 m- B
3. Find the value of El midway between the supports for the beam shown. Use the Super Position method. -5 m- 180 KN B m El = constant E = 70 GPa I = 2,340 (106) mm4 15 kN/m m-
Solve for the reactions, the midspan deflection, and the slope at the midspan. Use E = 70 GPa and I = 100 x 106 mm4 Final Equations with value of C1 and C2 EIy'' = EIy' = EIy = RA: RB: MA: Deflection: Slope:
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
Q.4) A pipe assembly is acted on by four forces and one couple moment. The 300 N force is parallel with the z-axis, the 130 N force is parallel with the y-axis, and the 60 N force is parallel with the x-axis. Force F, has a magnitude of 220 N and coordinate direction angles given by aA = 45°, BA = 60°, and YA = 120°. The couple moment M, is in the x-z plane and has a magnitude of 400 N-m. Determine the resultant moment about point B. Mc 30 300 N 1 m B0.5 m 0.75 m 0.75 m 130 N FA
Problem III. Solve the problem using Conjugate Beam Method. From the given fixed beam at both ends, solve the following questions using constant El. 12kN/m a. Reactions at A b. Reactions at B 4kN/m c. Slope at 6m from B in radians d. Displacement at 4m from A in mm 4m 6m