Please answer everything Water with flow rate of 12 lps from ground level is delivered to upper levels using the 50-mmdiameter pipe connection with a 30°-bend as shown in the figure. The combined weight ofthe bend and the fluid inside it is 50 N. Assume that the difference in elevation due to thebend and the losses through it are negligible.Determine the horizontal force required to keep the bend stationary.a.233.56 N →b.134.84 N →300c.63.51 N →d.36.67 N →Determine the vertical forcerequired to keep the bendstationary.a. 13.87 N 1b.183.02 N tc.156.18 Nd.84.84 N↓100 kPal50 mm

Answered: Image /qna-images/answer/1a61afe0-efa0-45a0-bc7f-263a3cdb8913.jpg

Determine the horizontal force required to keep the bend stationary. a.233.56 N → b.134.84 N → c.63.51 N → d.36.67 N → Determine the vertical force required to keep the bend stationary. a. 13.87 N 1 b.183.02 N 1 c.156.18 N d.84.84 N 30° 100 kPa 50 mm

Determine the horizontal force required to keep the bend stationary. a.233.56 N → b.134.84 N → c.63.51 N → d.36.67 N → Determine the vertical force required to keep the bend stationary. a. 13.87 N 1 b.183.02 N 1 c.156.18 N d.84.84 N 30° 100 kPa 50 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

• A bin holds three cylinders, each weighing 1200 N. The diameter of each cylinder is 600 mm. Assume frictionless surface. W А В Given: W W= 1200 N ERE C d = 0.6 m Determine: a.) Force at Point A b.) Reaction at Point D RF RG c.) Reaction at Point G ->
Part B: Water at 20 °C steadily flows through the reducing section at 70 kg/s. We know the following about the dimensions of the system • D1= 220 mm • D2 = 80 mm d1 P1 (1) Compute the average velocity at section 2. •{ m p2 d2
Q1: Determine the range of P for which the system of two blocks will be in equilibrium. Friction is negligible except for the surface under block B. 30° P B A 150 lb 100 lb Hs=0.2-
= What is the gauge pressure at point P in the figure? Assume g 플 Water Immiscible liquid of sp. gr. 1.6 P 0.8 m 1 m 10 m/s²
3-134 A system is equipped with two pressure gages and a manometer, as shown in Fig. P3-134. For Ah = š cm, deter- mine the pressure difference AP = P, - P. Air Ah Manometer fluid SG = 2.67 Oil SG = 0.87 P1 P2 FIGURE P3–134
A vertical triangular gate with Alcohol (SG = 0.78) on one side is shown in the figure. Determine the total resultant force acting on the gate and the location of the center of pressure. +dy 3ft Unit weight of the liquid (y) Value of hbar (h) Area of the rectangular gate (A) Hydrostatic Force (F) Value of (Igx) Value of ybar (9) Location of the Hydro.Force measured from the water surface of the gate inclined (yp) Ib/ f ft ft lb fi ft ft ***answer Hydrostatic Force F on the box below:
The 2kg collar is released from rest at A and slides down the inclined fixed rod in the vertical plane. The coefficient of kinetic friction is 0.40. Calculate the a. Velocity of the collarwhen the spring has been compressed 40mm b. Velocity of collar before it hits the spring
The diameter of a pipe changes gradually from 6 inches at A to 18 inches at B. A is 15 ft lower than B. If the pressure at A is 10 lbs per square inch and at B, 7 lbs per square inch when there are 5.0 cubic ft per second flowing, determine: a. the direction of flow. b. the frictional loss between the two points B. If in Problem 1 the direction of flow is reversed, determine the pressure at A if all other factors, including the frictional loss, remain the same. C. In Problem 1, determine the diameter of pipe at B in order that the pressure at that point will also be 10 lbs per square inch, all other factors remaining constant. D. Determine the discharge in Problem 1, assuming no frictional loss, all other conditions remaining as stated. E. What would be the difference in pressure in pounds per square inch between A and B, Problem 1, if there were 6.2 cubic ft per second flowing, neglecting friction.
• A bin holds three cylinders, each weighing 1200 N. The diameter of each cylinder is 600 mm. Assume frictionless surface. А В Given: W= 10 kN E d = 0.6 m Determine: a.) Force at Point A F G b.) Reaction at Point D c.) Reaction at Point G
7. A nozzle discharges 100 L/s with a velocity of 24 m/s and is inclined 45° downwards. The jet coming out of the nozzle strikes an unsymmetrical two-cusped vane that is moving at a velocity of 6 m/s along the horizontal plane. Half of the jet is deflected upwards 45°and the other half is deflected downwards 90°. Determine the x- and y-components of the force exerted by the jet on the vane. vane
In horizontal pipe, which of the following is constant? Pressure headElevation headVelovity head 12
The discharge flowing down the pipe is 0.03 m3/s and the pressure at 2 is 20kPa. Assuming the losses in the pipe is negligible. A U-tube is connected between points 1 and 2 to determine the difference in their pressure, what would be the value of y. Liquid flowing in the pipe is water