Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the ¾ in diameter pin is in double shear. NS: P = 19770 lb-f A 10 in. B 30° P 12 in.

Problem 5 The right-angle bar is supported by a pin at B and a roller at C. what is the maximum safe value of the load P that can be applied if the shear stress in the pin is limited to 20000 psi? the ¾ in diameter pin is in double shear. NS: P = 19770 lb-f A 10 in. B 30° P 12 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A single-phase 111-V, 50-Hz supply is connected to a coil with 200 turns of a coil-core assembly as…

A: Given, Voltage RMS , E = 111 V Frequency (f) = 50 Hz Number of turns (N) = 200

Q: Vane tester with a diameter d = 9.1 cms and a height h = 18.2cms requires a torque of 120 to shear a…

Q: A theodolite is set up at station A and a 3 m long staff is held vertically at station B. The…

Q: A) Classify the soil with the following properties according to the USCS. % passing Dia (mm) 100 4.0…

A: Given: % Passing 100 100 91.5 79.2 58.7 36.5 L.L = 33% Diameter, mm 4 2 0.84 0.42 0.149 0.075…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³ at 3.3…

A: Given: A Liquid compressed in cylinder has, Volume of 1000 cm3 at 2 MN/m2 Volume of 993 cm3 at 3.3…

Q: 3: Determine the displacement and the slop at point D. Use the principle of virtual work. El is…

Q: Size of sample No. of +ve results No. of -ve. results 4 1 3 2 2 0 1 0.1 0.01 0.001 3 5 Determine the…

A: Given data- To Find- The value of MPN using Thoma's equation.

Q: Solve all please Q2) Choose the right answer. 1. The uncontrolled flow of whole mud into a formation…

A: 1. The uncontrolled flow of whole mud into a formation is known as lost circulation. Option C. 2.…

Q: 40° K 20° Wise Chains W F = 35 lbs

A: GIVEN: TO CALCULATE: Solve for the v- and w-components

Q: 1. Identify the 7 steps in Sprinkler System Design Calculation

A: The question has asked to identify 7 steps in Sprinkler System Design. Sprinkler Irrigation system…

Q: A town has an existing horizontal sedimentation flow tank with an overflow rate of 17 m³/day/m², and…

Q: On a road, the speed - density relationship of a traffic stream is given by u = 70 - 0.7 k (where…

A: Given Data Speed-density relationship of a traffic u = 70 - 0.7k Find the average time headway at…

Q: A vertical parabolic curve is to be used as a grade-separation structure. The curve is 242 m long…

A: Here's the calculation: First, we need to find the parabolic constant (K) using the formula: K = (G2…

Q: A beam is subjected to equal bending moments of M₂ = 2800 N-m. The cross-sectional dimensions are b=…

Q: Given the vertical and horizontal stresses acting on an infinitesimal element of soil within a…

A: The stress acting on a vertical and horizontal plane are minor and major principal stress…

Q: A student began an experiment for the determination of 5-day, 20°C BOD on Monday. Since the 5th day…

Q: For the given ground conditions, the time (in days, rounded to the nearest integer) required for 90%…

Q: sand layer; K = 1 m/d; thickness = 6 clay layer; K = 0.000001 m/d; thickness=0.7 m sand layer; K= 1…

Q: A beam is subjected to equal bending moments of M₂ = 57 kip-ft. The cross-sectional dimensions are…

Q: Explain the step-by-step process of the methodology for lot area sketch plan preparation. Give…

A: The lot area sketch plan A lot area sketch plan is a rough drawing that shows the layout of a piece…

Q: Use the virtual work method to determine the horizontal deflection at joint E of the frame shown in…

Q: Solve for the shear and moment equations and draw the shear and moment diagrams of the following…

Q: A prestresed concrete T-beam shown has a simple span of 9m and to be pre-stressed with tendons…

A: Prestress Concrete: Prestressed concrete is a technique designed to generate enough precompression…

Q: 4) Determine the increase in vertical stress at a depth (2) m belowpoint A due to surface loads…

Q: Given a-4 m and b-10 m, locate the x coordinate of the center of mass of the compound homogeneous…

Q: This question about Sanitary Engineering ........................ involve a physical change such as…

A: Treatment methods have been broadly classified as Unit Operations Unit Process

Q: 20. A CIS33.9 of A36 channel to serve as a roof edge beam with a simple span of 25 ft. The nominal…

Q: why is column flotation can be very useful if floor space is at a premium

A: Column flotation consist of column which transmits loads to a beam member of structure. This means…

Q: A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the…

A: Given Dimeter of wooden stave barrel = 3.5 ft Height of wooden stave barrel = 5 ft Specific gravity…

Q: After the sample has been fractured and reassembled, the gage marks that initially measured 2.000”…

Q: A symmetrical three hinged parabolic arch has 40 m span and 5 m rise. A vertical downward load of 30…

Q: Solve for the elements of Simple Curves T, L, C, E, M with D = 3° and I =36° with English System…

Q: Average free flow speed and the jam density observed on a road stretch are 60 km/h and 120…

A: Given- Average free flow Vf=60 km/h, Jam density Kj=120 veh/km Maximum flow=?

Q: 3 - Given Young's modulus E, Poisson's ratio, and normal stress in the negative x-direction, what y…

Q: Scale factors figures must be the same proportions on all sides from the original figure.

A: This question is related to Building Drawings and Design from Civil Engineering. In this question…

Q: *2-20. Determine the reactions on the b SOLUTION Equations of Equilibrium. Referring to the FBD of…

Q: Determine the x-coordinate of the centroid of the shaded area by integration. 1 12 11 Answer: x= 15…

Q: 3. A steel plate 5/16 in. thick is embedded in a horizontal concrete slab and is used to anchor a…

Q: 1-91. The 60-kg flowerpot is suspended from wires AB and BC. If the wires have a failure normal…

Q: Replace the two forces acting on the bent pipe by a single equivalent force R. Specify the distance…

Q: PART 2. Answer the following using Area Moment Method Problem 1. Determine the deflection and slope…

Q: Determine the tensile stress @section a-a considering the red trapezoidal plate

Q: For the rectangular foundation (2.5m x 3m) shown in the figure, compute the net allowable bearing…

Q: Question 4 16 Points A tall open-topped standpipe has an inside diameter of 1320 mm and a wall…

A: Given data, Inside diameter of the stand-pipe = 1320 mm = 1.32 m Wall thickness (t) = 8 mm = 0.008…

Q: 3. Determine the magnitude and location of the total hydrostatic force acting on the 2 x 4 m gate…

A: Given, Area of gate = 2m x 4m

Q: A cantilever timber beam with a span of L = 2.2 m supports a uniformly distributed load w. The beam…

Q: 1. Write the total potential energy function for the pulley system shown below, assuming that the…

Q: A beam is subjected to equal bending moments of M₂ = 3800 N-m. The cross-sectional dimensions are b…

Q: Given the layout shown in Figure (2) and the following data: A. Proportion a combined footing for a…

Q: W 10k b Á

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

Problem 5
The right-angle bar is supported by a
pin at B and a roller at C. what is the
maximum safe value of the load P that
can be applied if the shear stress in the
pin is limited to 20000 psi? the 3/4 in
diameter pin is in double shear.
ANS: P = 19770 lb-f
A
10 in.
B
30°
P
12 in.
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

F5. The circular shaft AC is fixed to rigid walls at A and C. The section AB is solid annealed bronze and the hollow section BC is made of aluminum alloy 2024 T-4. There is no stress in the shaft before the 20,000 ft-lb torque is applied. Determine the maximum shearing stress in each shaft after T is applied. Section BC 4 D=4" 20 ft-k 6.5-FE B 5ft Match each item to a choice: TAB TBC 2"
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
A mechanic uses a crowfoot wrench to loosen a bolt at E. Knowing that the mechanic applies a vertical 20-lb force at A, determine the principal stresses and the maximum shearing stress magnitude at point Hlocated as shown on top of the 4 -in. diameter shaft. (Round the final answers to two decimal places.) H E 6 in. B 10 in. The maximum principal stress is Omax |ksi and the minimum principal stress is Omin |ksi (+ tensile; - compressive). The maximum shearing stress magnitude is ksi.
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
(6) The tension member is fastened together using two bolts, one on each side of the member as shown. Each bolt has a diameter of 12 mm. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is Tallow 80 MPa and the allowable average normal stress is allow= 120 MPa. A000 60° P
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. 150 P=300lb. -5 in- dw ↓ 1 4 in. D View a-a of B
Q 3: -Knowing that the bracket AB has a uniform thickness of in., determine (a) the principal planes and principal stresses at point H. (b) the maximum shearing stress at point H. 3 kips 30° L 5 in.- 0.75 in. K.. H. 1.25 in. B 2.5 in.
The bell-crank mechanism is in equilibrium for an applied load of P = 35 kN. Assume that a = 240 mm, b = 185 mm, and 8 = 65°. The pin at B has a diameter of d = 15 mm, and the bell crank has a thickness of t = 12 mm. Calculate the average shear stress in the pin at B. (1) P Answer: T = i Bell crank A 269.337 a C MPa B Support bracket- b F₁ it B
Strain in rods is zero prior to applying load Determine load P such that the axial stress in the steel pipe is 200 MPa P Imm GAP RIGIO PLATE .6m B RIGID SUPPORT 30 mm x 30 mm. AL BAR E = 73 GPA 100 mm E = 200 G PO A B A ØSTEEL PIPE w/ 5mm WALL
Prolem2 -compute the maximum force P that can be applied by the machine operator, if the shearing stress in the pin at B and the axial stress in the control rod at C are limited to 4000 psi and 5000 psi, respectively. The diameters are 0.25 inch for the pin, and 0.5 inch for the control rod. Assume single shear for the pin at B. 2. I10 6 in 2 in
☑ How Find max. tensile and comporsive stresses. P 5KN.M 15AN Im 2m 2m B A IN.A= 60×10 mm" 60 12
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.