The force-elongation curve for a material is given below. The sample was a cylindrical rod with an initial diameter of 1 cm and a length of 10 cm. Determine the modulus, yield strength, tensile strength and % elongation for this material. 250 200 150 100 50 10 10.1 10.2 10.3 Length (cm) Force (kN)

The force-elongation curve for a material is given below. The sample was a cylindrical rod with an initial diameter of 1 cm and a length of 10 cm. Determine the modulus, yield strength, tensile strength and % elongation for this material. 250 200 150 100 50 10 10.1 10.2 10.3 Length (cm) Force (kN)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid plastic rod has a diameter of d = 18 mm and a length of L = 700 mm. An axial load of P = 33 kN is applied to the rod as shown. The elastic modulus is E = 2.0 GPa and Poisson's ratio for this material is v= 0.41. Determine the magnitude of the change in the rod diameter Ad for the given load. Answer: Ad = i mm
A plastic rod with length and radius of 300 mm and 30 mm, respectively. If an axial force of 400 N is applied, estimate the length and diameter change. Young’s modulus and Poisson’s ratio of the material are 2.7 Gpa and 0.4 respectively.
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
A solid plastic rod has a diameter of d = 21 mm and a length of L = 600 mm. An axial load of P = 24 kN is applied to the rod as shown. The elastic modulus is E = 2.6 GPa and Poisson's ratio for this material is v=0.37. Determine the magnitude of the change in the rod diameter Ad for the given load. tel Answer: Ad= i Ja ↑ L mm
A student wants to measure the strain at a particular point K on a loaded specimen, so she affixes a 45° strain rosette at point K and obtains the following results: €A = 390 μrad EB = 275 μrad Ec = 325 prad After packing up and going home to analyse her results, she realises that the strain rosette was misaligned by 0 degrees CW (where a negative corresponds to CCW) from the x-y axes-ie. Gauge C is not parallel with the x-axis and is instead parallel with a different x' axis that is rotated by 0 degrees-where: 0 = 16 deg Instead of replacing the rosette and retaking measurements, the student realises she can use what she learned in ENGG2400 to find the strains she's interested in. b 45° 45° a) Draw a diagram of the situation, showing both the x-y axes and the strain rosette. b) Calculate Exx, Eyy and Yxy. c) Calculate the maximum in-plane shear strain and the associated average normal strain. I X
Osec σij = The hydrostatic stress for the state of stress represented by oij given below is MPa [100 50 50 125 75 75 75 = 50 50 1 MPa
The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can be approximated as shown. The wing is subjected to a torque of 4.7 MN m and the wall thickness is 10 mm. The wing is made of 2014-T6 aluminum alloy. Figure 1 of 1 0.5 m 10 mm 10 mm 10 mm 2 m 0.25 m 0.25 m Express your answer with the appropriate units. Tavg 124 MPa Submit Correct Part B My Answers Give Up Determine the angle of twist per meter length of the wing. Express your answer with the appropriate units. VΠΙ ΑΣΦ It vec Submit My Answers Give Up Incorrect; Try Again; 5 attempts remaining ? °/m
The representative curves of the applied stress versus the number of cycles for different metals are shown in Figure Q2. Analyze both metals in terms of fatigue properties. 500 Stress amplitude (MN/m²) 400 300 200 100 0 1045 steel 10³ 104 2014-T6 aluminium 10⁹ 106 107 Number of cycles, N₂ Figure Q2: Representative curves of stress amplitude vs number of cycles 108 10⁹
A solid plastic rod has a diameter of d = 31 mm and a length of L = 500 mm. An axial load of P = 34 KN is applied to the rod as shown. The elastic modulus is E = 2.0 GPa and Poisson's ratio for this material is v= 0.38. Determine the magnitude of the change in the rod diameter Ad for the given load. Įd Answer: Ad= i L mm