3.5-6 A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the applied torque reaches the value T = 500 N · m. At this value of torque, a strain gage oriented at 45° to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material? Strain gage Įd = 50 mm T= 500 N - m T 45° PROBLEM 3.5-6 25-7

3.5-6 A solid circular bar of diameter d = 50 mm (see figure) is twisted in a testing machine until the applied torque reaches the value T = 500 N · m. At this value of torque, a strain gage oriented at 45° to the axis of the bar gives a reading e = 339 × 10-6. What is the shear modulus G of the material? Strain gage Įd = 50 mm T= 500 N - m T 45° PROBLEM 3.5-6 25-7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

5. The aluminum alloy bar has a circular cross section with 20-mm diameter and a shear modulus of 28 GPa. What is the magnitude of the maximum shear stress in the bar due to the uniformly distributed torque? y 8.5 kN-m/m 120 mm
Urgent , Handwritten solution. Don't copy paste
At a point in a machine component that is subjected to plane stress, the normal and shear stresses are σx=σx= 100 MPa, σy=σy= 20 MPa, and τxy=τx⁢y= 28 MPa, acting in the directions shown in the figure. At this point, determine the strain components εxεx, εyεy, εzεz, and γxyγx⁢y. Assume that E = 68 GPa and v = 0.32 for the machine component.
STRENGTH OF MATERIALS. Please show the complete solutions. NO LONG EXPLANATION NEEDED! Rate will be given. Answer ASAP! Please answer all. MULTIPLE CHOICE: CHOOSE THE CORRECT ANSWER 1. Using MOHR CIRCLE from the given stresses on two perpendicular planes what is the normal stress on plane a-a? a. 75 MPa b. 150 MPa c. 125 MPa d. 100 MPa
Q: A piece of material is subjected to tensile stress of 70 N/mm² in one direction and a compressive stress of 50 N/mm² in a direction at right angles to the previous one. Find fully the stresses on a plane the normal of which makes an angle of 40 degree with the 70 N/mm2 stress.
NEED ASAP. SOLVE CORRECTLY AND PROVIDE DETAILED SOLUTIONS. ALSO PROVIDE THE FBD PLEASE
Answer asap with solution
Answer the problem and show your solution and box the final answers. I will immediately give a rating and like for the answer.
Can you solve this questions?
A 20 KN weight is suspended by two wires as shown in the figure. The length of each wire is 2 meter. The steel wire (E value 200 GPa) has a cross-sectional area of 60 x 10-6 m² and the aluminum wire (Evalue 70 GPa) has a cross-sectional area of 120 x 10-6 m². The stress in aluminum wire is Aluminum Steel 20 kN
10.Stress transformation. From the figure below, find the orientation of the maximum principal stresses, the magnitudes of the maximum principal stresses and the maximum shear stress. All formulae given at the end of the exam. 2/22 27200005 27200032 10 MPa 40 MPa 50 MPa
An 18-m-long steel wire of 10-mm diameter is to be used in the manufacture of a prestressed concretebeam. It is observed that the wire stretches 55 mm when a tensile force P is applied. Knowing that E=250GPa, determine (a) the magnitude of the force P, (b) the corresponding normal stress in the wire