Determine the strain (ε) for each material if the applied axial stress is 200 MPa. Show all your work, and present the final answer in table format. You will search for properties of materials and tabulate properties. Complete Table 1 below forthe physical and mechanical properties of the given specimen materials. Note that the initiallength (Li) of the specimens is 250mm.Table 1. Test specimens: physical and mechanical propertiesUltimateElasticYieldSpecimenDensityTensileModulusStrengthMaterialStrength(kg/m³)(GPa)(МPа)(МPa)Aluminium2,710 kg/makg/m36927690Brass8470 kg/m3kg/m3117140360Copper8960 kg/makg/m313033.3210Steel7860 kg/mskg/m3200350420

GIVEN DATA SPECIMEN MATERIAL ELASTIC MODULUS E (GPa) ELASTIC MODULUS E (N/mm2) ALUMINIUM 69…

You will search for properties of materials and tabulate properties. Complete Table 1 below for the physical and mechanical properties of the given specimen materials. Note that the initial length (L.) of the specimens is 250mm. Table 1. Test specimens: physical and mechanical properties Ultimate Elastic Yield Specimen Density Tensile Modulus Strength Material (kg/m) Strength (GPa) (MPa) (MPa) Aluminium 2,710 kg/makg/m3 69 276 90 Brass 8470 kg/makg/m3 117 140 360 Copper 8960 kg/m3kg/m3 130 33.3 210 Steel 7860 kg/mskg/m3 200 350 420

You will search for properties of materials and tabulate properties. Complete Table 1 below for the physical and mechanical properties of the given specimen materials. Note that the initial length (L.) of the specimens is 250mm. Table 1. Test specimens: physical and mechanical properties Ultimate Elastic Yield Specimen Density Tensile Modulus Strength Material (kg/m) Strength (GPa) (MPa) (MPa) Aluminium 2,710 kg/makg/m3 69 276 90 Brass 8470 kg/makg/m3 117 140 360 Copper 8960 kg/m3kg/m3 130 33.3 210 Steel 7860 kg/mskg/m3 200 350 420

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A1 Copy the sketch of the tensile stress-strain test (Figure A1) results for a waisted metallic specimen and indicate the locations representing maximum stress (A), ultimate strain to failure (B), and 0.2% proof (yield) stress (C), and calculate the Young's modulus of the material. Figure A1 300 250 200 150 100 50 0 Stress (MPa) 0.2 0.4 0.6 8.0 Strain (%) 10.0
The following data were collected from a 0.4-in.-diameter test specimen of polyvinyl chloride (l0 5 2.0 in.): Load (lb) 0 Δl (in.) 0.00000 300 600 900 1200 1500 1660 1600 0.00746 0.01496 0.02374 0.032 0.046 0.070 (maximum load) 0.094 1420 0.12 (fracture) After fracture, the total length was 2.09 in. and the diameter was 0.393 in. Plot the engineering stress strain curve and calculate (a) the 0.2% offset yield strength; (b) the tensile strength; (c) the modulus of elasticity; (d) the % elongation; (e) the % reduction in area; (f) the engineering stress at fracture; and (g) the modulus of resilience.
Fatigue test results of a material are shown in the diagram. a) Estimate the ultimate static strength of this material b) Estimate the fatigue (endurance) limit. c) If this test specimen has a cross-sectional area of 14 cm² and subjected to a maximum repeated load of 2800 kg over it, after how many repetitions will it fail? d) Determine the fatigue strength at 1000 cycles a (kgf/cm?) 500 400 300 200 100 2 3 4 5 6 logio N
A sample of metal having a rectangular cross-section; a width of 10.00 in. and a thickness of 0.25 in. is cold worked to a final width of 9.50 and a thickness of 0.20 in. If the plastic behavior of this sample is given by d=100,000€0.5 psi, determine the new yield strength of the sample after cold working.
Q4/ A. Explain why ceramic materials do not response to the plastic deformation processes? Also clarify why flexural test is applied to ceramics instead of tensile test? B. Estimate whether a cylindrical aluminum oxide sample will fail or not when it subject to flexural test to achieve flexural strength of 390 MPa knowing that the sample radius is 2.5 mm, separation distance is 30 mm, and the applied load is 620 N respectively.
3. Given the following fatigue data for a brass alloy: Cycles to Failure 2 x 105 1х 106 Stress Amplitude (MPa) 310 223 191 3х 106 168 1 x 107 153 3х 107 143 1х 108 134 3х 108 127 1х 109 a.) Plot the S-N curve for this alloy. b.) Does this material have an endurance limit? Explain. c.) Determine the fatigue strength at 5 x 105 cycles. d.) Determine the fatigue life for 200 MPa. e.) If the loading in part c is uniaxial, what is the minimum diameter of a circular rod required for this application if the maximum load is 500 kN?
I In a compression test and for a very ductile material similar to copper , the diameter and the length of the specimen before the test were 60mm and 80mm respectively . Find the length , in inches , after the test if the diameter became 120mm . Assume that the density remained unchanged
A brass alloy rod having a cross sectional area of 100 mm2 and a modulus of 110 GPa is subjected to a tensile load. Plastic deformation was observed to begin at a load of 39872 N.a. Determine the maximum stress that can be applied without plasticdeformation.b. If the maximum length to which a specimen may be stretched withoutcausing plastic deformation is 67.21 mm, what is the original specimenlength?
The (G-E) diagram obtained in the tensile test performed on a metal sample with a diameter of 16 mm is as follows. The loads at points A, B and C and the elongation measured on l. 16 cm gauge length were determined as follows: B A B C Load (kgf) 4800 8400 7200 Elongation (mm) 0.192 28.8 38.4 a) Calculate the proportionality limit, modulus of elasticity, tensile strength, maximum uniform elongation, and contraction-elongation ratio of the metal. b) Since the measured diameter of the metal at break is 12 mm, find the constriction ratio and the actual stress at break.
3. Consider iron and its elastic constants (Find them from the net or some book). An iron specimen consists of grains with texturing distribution of [110] (20%), [112] (20%), [111] (30%) and [103] (30%) (all percentages by volume) along the loading direction is serving under a static force of 10,000 N. The metal rod has a 20 mm diameter perpendicular to the loading direction. a) Find the strain response of the specimen.
what is the importance of the stress concentration test? I NEED IT RIGHT NOW, PLEASE HELP ME. I WILL RATE IT.
Stress-strain plot for a metal is given below. Determine the following: a) Modulus of elasticity. b) Yield strength by 0.2% off-set method. c) Tensile and fracture strengths. d) Maximum load that can be sustained by a cylindrical specimen having an original diameter of 15.3 mm. e) If a specimen having an original length of 320 mm and elongation is measured as 2.56 mm, determine the applied stress. 450 400 350 300 250 200 150 100 50 0.002 0.004 0.006 0.008 0.01 0.012 0.014 0.016 Strain Stress (MPa)