The drive drum of a belt conveyor consists of a rope and a pulley. It is stretched by a tensioning mechanism. The rope in the mechanism is where the drive drum is fixed to the center; of a reel located horizontally outside the drum designed in such a way that weight is hung on the end by passing it around. Belt conveyor It is stretched with a force of 4000 kg. Shrinkage in the belt conveyor force is 1900 N and the friction coefficient between the drum and the belt is 0.12. by; What is the angle of wrapping of the belt to the drum?

The drive drum of a belt conveyor consists of a rope and a pulley. It is stretched by a tensioning mechanism. The rope in the mechanism is where the drive drum is fixed to the center; of a reel located horizontally outside the drum designed in such a way that weight is hung on the end by passing it around. Belt conveyor It is stretched with a force of 4000 kg. Shrinkage in the belt conveyor force is 1900 N and the friction coefficient between the drum and the belt is 0.12. by; What is the angle of wrapping of the belt to the drum?

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.9P: A safety valve on the top of a tank containing steam under pressure p has a discharge hole of...

See similar textbooks

Similar questions

A safety valve on the top of a tank containing steam under pressure p has a discharge hole of diameter d(see figure). The valve is designed to release the steam when the pressure reaches the value Pmax If the natural length of the spring, is L and its stiffness is k, what should be the dimension ft of the valve? (Express your result as a formula for h.)
The mechanism in the figure below is designed to maintain the horizontal position of the load while lifting it up.The pin located around the outer circumference of the r cm diameter pulley can slide frictionlessly in the channel on the ABC arm.The length of each of the ABC and DE arms is r cm and the weight of the lifted load is m kg.The mechanism is lifted upwards by pulling the rope wrapped around the pulley. The force P required to be applied to the rope to keep the load b cm above the ground and all the forces acting on the ABC arm Please specify. а ст P. с ст b cm а ст a=34cm ,b=68cm , c=20cm ,r=93cm ,m=110kg
Q3/ A screw-jack is used to lft a load of 4 kN. The screw of the screw-jack is square threaded with two threads to 1 cm. If the co-efficient of friction between the nut and screw is 0,095 and outer diameter of screw s 6 cm, find the force required atthe end of the handle of length 50 cm to ift the load. (20 M)
Calculate the rection forces when the radius of the pulleys are 0,1 m and K = 1200 N.
The following data is referring to a screw jack. The vertical load on the screw = 20kN Force applied at the lever end whose length = 80cm The mean radius of the screw = 2.5cm Pitch of the screw =1cm Co-efficient of friction between the screw thread and the nut = 0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
The following data is refers to a screw jack. The vertical load on the screw320kN Force applied at the lever end whose length=80cm The mean radius of the screw=2.5cm Pitch of the screw=1cm Co-efficient of friction between the screw thread and the nut=0.15 Determine the force on the lever end while raising the load and efficiency of the screw jack
Q2/ A belt drive consist of two V-belts in parallel, on grooved pulleys of the size. The angle of the groove is 30°. The cross – section area of each belt is 750 and u is 0.12. The density of the belt material is 1.2 Mg/m' and the maximun stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 mapart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted
5. An open belt 100 mm wide connects two pulleys mounted on parallel shafts with their centres 2.4 m apart. The diameter of the larger pulley is 450 mm and that of the smaller pulley 300 mm. The coeffi- cient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be trans- mitted. [Ans. 2.39 kW]
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 165o and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted.
2. The pressure of a hydraulic working cylinder is intensified by using a pressure intensifier. The intensifier have area A₁ against the pump pressure pp and area A2 against the load pressure PL. a) Calculate the pressure ratio A₁/A2 needed to lift the mass m=20000kg, when the pump pressure pp=280bar and work force resisting the piston motion Fw=100kN. The piston diameter D=80mm. pp is approximated to be constant. Losses, including the directional valve loss, are neglected. A₂ PL b) What is the lifting speed of the mass, if the pump flow Q₁ is 120 1/min.
A 125 kg wheel with a radius of 2.50 m is being pulled up an incline by a 550 kg horse. There is a 45.0 cm high protrusion in the incline, as shown in the figure. What is the tension in the rope when the wheel is just beginning to lift off the incline to go over the protrusion? What is the minimum possible coefficient of static friction between the horse and the incline for the horse to be able to pull the wheel over the protrusion?