A polyethylene bar having rectangular cross section with a width 6.36 in. and depth 6 in. is centered inside a hollow steel square section with side dimension of 7 in. The polyethylene bar is then compressed by an axial force P. 0.3 in. 6 in. 7 in. 6.36 in 7 in. At what value of the force P will the gap between the polyethylene bar and the steel tube be closed for the first time in one dimension? For polyethylene, assume E = 200 ksi and v = 0.4. Assume that the material behaves linearly elastically. (Enter the magnitude in kips.) kips What is the remaining gap between the polyethylene bar and the steel tube in the other dimension? (Enter the distance in inches between the side of the polyethylene bar and the closest side of the steel section.)

A polyethylene bar having rectangular cross section with a width 6.36 in. and depth 6 in. is centered inside a hollow steel square section with side dimension of 7 in. The polyethylene bar is then compressed by an axial force P. 0.3 in. 6 in. 7 in. 6.36 in 7 in. At what value of the force P will the gap between the polyethylene bar and the steel tube be closed for the first time in one dimension? For polyethylene, assume E = 200 ksi and v = 0.4. Assume that the material behaves linearly elastically. (Enter the magnitude in kips.) kips What is the remaining gap between the polyethylene bar and the steel tube in the other dimension? (Enter the distance in inches between the side of the polyethylene bar and the closest side of the steel section.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel pipe of length L= 5 ft, outside diameter d₂= 9.3 in., and inside diameter d₁= 5.1 in. is compressed by an axial force P= 577 kips. The material has Poisson's ratio v=0.30. Determine the increase in inner diameter. A
A polyethylene bar having rectangular cross section with a width 7.35 in. and depth 7 in. is placed insidea hollow steel square section with side dimension of8 in. The polyethylene bar is then compressed by an axialforce P. At what value of the force P will the gap betweenthe polyethylene bar and the steel tube be closed for thefirst time on one side? What is the remaining gap betweenthe polyethylene bar and the steel tube on the other side?For polyethylene, assume E 5 200 ksi and n 5 0.4.1
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef = 1080 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). F RIGID PLATE ALUMINUM FACE PLATE FOAM L2 +4₁ 43 L1
The uniform 44 kN bar BC is supported by a pin at C and the aluminum wire AB. The cross-sectional area of the wire is 178.5 mm2. Assuming bar BC to be rigid, find the vertical displacement of B due to the weight of the bar. Use E = 71 GPa for aluminum. Anwer must be in mm.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding. 24m
A triangular dam is shown in the figure, base is 6-m and height is 8-m. Compute for the factor of safety against sliding and overturning. Unit weight of concrete is 23.54 kN/cu.m. Consider 1 meter length strip. Disregard hydrostatic uplift pressure. The coefficient between the dam and the foundation is 0.8. h
The dimensions of the compressed air tank manufactured in the form of a cylinder are given in the figure. The tank is manufactured by joining a 6 mm thick steel plate with a helical weld at an angle of 30°. Since the safe shear stress in the direction parallel to the weld seam is 30 MPa, calculate the maximum pressure that can be used in the tank.
(c) The cross section of a quarter circular concrete block XYZof width 1.8m is shown in Figure 3. The specific weight of the concrete mix is 24 kN/m3. The hinge is along XX. Calculate the vertical force R at Y to hold the gate in this position. K Fixed slab 1.2 m Y W Fy 1.3 m FĦ D B Figure 3
1. An underwater vehicle that can be approximated as a sphere of radius r = 0.8 m is to operate at depth h=1000 m. It is constructed by joining two hemispheres with 40 equally spaced bolts, Figure Q1. The allowable stress for the bolts is 100 MPa. The sphere is filled with air at pressure p = 600 kPa. If the material of the sphere is steel with yield stress gx=600 MPa, and the factor of safety is n = 2.5 with respect to yielding, calculate the bolt diameter d and the required thickness of the sphere t. Assumptions: (a) The sphere may be treated as a thin-walled pressure vessel. (b) The sea water density p= 1000 kg/m³. (c) Buckling of the vessel will not occur. Spherical Vessel Bolts used to fix two hemispheres to each other 0.8 m Figure Q1
An aluminum pole for a street light weighs4600 N and supports an arm that weighs 660 N (seefigure). The center of gravity of the arm is 1.2 m from theaxis of the pole. A wind force of 300 N also acts in the (-y)direction at 9 m above the base. The outside diameter ofthe pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressivestresses σt and σc, respectively, in the pole (at its base)due to the weights and the wind force.
The P load applied to a steel bar is transferred to the board by an annular washer. The diameter of the rod is 34mm and the inner diameter of the washer is 35.7 mm. Since it is known that the axial normal stress on the steel bar is 119 MPa, and the average bearing stress between the washer and the board should not exceed 34 MPA, how many mm is the smallest allowable outer diameter of the washer?
A circular plate with simply supported edges subjected to a uniform pressure of P=1,450 KPa, as shown below, is considered. The plate thickness is h=8 mm, and the plate radius is RO=540 mm. If Young's modules and Poisson's ratio are assumed to be E=80 GPa and 1=0.4, respectively, workout the absolute maximum circumferential stress of the plate edge in GPa. (NOTE: round-off your answer to 4 decimal places, and write your answer without considering the negative (-) sign). 8 P Ro