The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; 1 = 350 × 106 mm4]. Assume P = 35 kN, w = 20 kN/m, LAB = 1.50 m, and LBC = 2.25 m. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. A LAB B Answer: VA,w= W LBC Determine the component of the beam deflection at point A due to only the uniformly distributed load of w = 20 kN/m. X mm.

The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; 1 = 350 × 106 mm4]. Assume P = 35 kN, w = 20 kN/m, LAB = 1.50 m, and LBC = 2.25 m. For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. A LAB B Answer: VA,w= W LBC Determine the component of the beam deflection at point A due to only the uniformly distributed load of w = 20 kN/m. X mm.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.3.16P: A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable...

See similar textbooks

Similar questions

A fixed-end b earn is subjected to a point load at mid-span. The beam has a rectangular cross section (assume that the h/b ratio is 2) and is made of wood (E = 11GPa). Find height h of the cross section if the maximum displacement of the beam is 2 mm. Calculate the displacement of the beam at the inflection points.
A simple beam with an overhang is subjected to d point load P = 6kN. If the maximum allowable deflect ion at point C is 0.5 mm, select the lightest W360 section from Table F-l{b) that can be used for the beam. Assume that L = 3 m and ignore the distributed weight of the beam.
A beam ABC is fixed at end A and supported by beam DE at point B (sec figure). Both beams have the same cross section and are made of the same material. Determine all reactions due to the load P. What is the numerically largest bending moment in cither beam?
-3 The deflection curve for a simple beam AB (see figure) is given by v=q0x360LEI(7L410L2x2+3x4) Describe the load acting on the beam.
-5-7 A cantilever beam AB carries three equalaly spaced concentrated loads, as shown in the figure. Obtain formulas for the angle of rotation B and deflaction B at the free end of the beam.
Beam ACB hangs from two springs, as shown in the figure. The springs have stiffnesses Jt(and k2^ and the beam has flexural rigidity EI. What is the downward displacement of point C, which is at the midpoint of the beam, when the moment MQis applied? Data for the structure are M0 = 7.5 kip-ft, L = 6 ft, EI = 520 kip-ft2, kx= 17 kip/ft, and As = 11 kip/ft. Repeat part (a), but remove Af0 and instead apply uniform load q over the entire beam.
A simple beam ACE is constructed with square cross sections and a double taper (see figure). The depth of the beam at the supports is dAand at the midpoint is dc= 2d 4. Each half of the beam has length L. Thus, the depth and moment of inertia / at distance x from the left-hand end are, respectively, in which IAis the moment of inertia at end A of the beam. (These equations are valid for .x between 0 and L, that is, for the left-hand half of the beam.) Obtain equations for the slope and deflection of the left-hand half of the beam due to the uniform load. From the equations in part (a), obtain formulas for the angle of rotation 94at support A and the deflection Scat the midpoint.
The deflection curve for a cantilever beam AB (see figure) is given by v=q0x2360L2EI(45L440L3x+15L2x2x4) Describe the load acting on the beam. Determine the reactions RAand M 4at the support.
A simple beam AB of length L is subjected to loads that produce a symmetric deflection curve with maximum deflection S at the midpoint of the span (see figure). How much strain energy U is stored in the beam if the deflection curve is (a) a parabola and (b) a half wave of a sine curve?
A weight W = 4000 lb falls through a height h = 0.5 in, onto the midpoint of a simple beam of length L = 10 ft (see figure). Assuming that the allowable bending stress in the beam is = 18,000 psi and E = 30 x 10* psi, select the lightest wide-flange beam listed in Table F-l(a) in Appendix F that will be satisfactory.
Copper beam AB has circular cross section with a radius of 0.25 in. and length L = 3 ft. The beam is subjected to a uniformly distributed load w = 3.5 lb/ft. Calculate the required load P at joint B so that the total deflection at joint B is zero. Assume that£ = 16,000 ksi.
What is the span length L of a uniformly loaded, simple beam of wide-flange cross section (see figure) if the maximum bending stress is 12,000 psi, the maximum deflection is 0.1 in., the height of the beam is 12 in., and the modulus of elasticity is 30 × 106psi? (Use the formulas of Example 9-1.)