What is the temperature, in K, of the O2 in the final state?

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: On the attached drawing 11A005< what is dimension "G"

A:

Q: Can you help me with this problem?

A: The image shows a part drawing for a wire electric discharge machine (EDM). The objective is to…

Q: , how do you add vectors using parallelogram method graphically

A: Vector can be a quantity that has some magnitude and have a specific direction. displacement,…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Successive approximation ADC explian

A:

Q: In the context of our teaching and learning, which one of the below statements is mostly correct…

A: The correct option is three The tolerance is determined by the function.

Q: The input D rotates at 200 rpm clockwise viewed from the left with a torque of 40 Nm. The efficiency…

A: Given: Speed of input DIs=200 rpm Torqueτ=40 Nm Efficiency η=75%

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: Compute the following: Basic size Tolerance Maximum limit size Minimum limit size

A: Machine drawing is the drawing in which component details are given in geometrical view. For…

Q: Briefly describe the action taken by the following G&M command blocks assuming absolute coordinates.…

A:

Q: For the following figure assume the box as 10 mm and sketch the following view using CREO PARAMETRIC…

A:

Q: None

A: Step 1:Identify the Components:The hand brake lever mechanism consists of three key links: the…

Q: Let A = (6), B = (,), and C C) be points in II. Define the points %3D D, 3D A + B — С %3 = (_;), D2…

A:

Q: Draw the isometric view of the following object given in orthographic projection.

A:

Q: . VELOCITY ANALYSIS. For the single-degree-of-freedom mechanism shown below, the angular velocity on…

A:

Q: What is the period in seconds?

A: To determine: The time period for the swing, where it takes approximately 2 seconds to reach on side…

Q: Figure shows the design of a taper turning operation performing on a lathe machine. D1 D2 d D3 L3 L1…

A: Basics of trignometry.

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: Using the drawing below identify th mistake on dimensioning rules and write the correct method to…

A: According to DG&T standards, there are 5-dimensional mistakes that are highlighted in the fig…

Q: Give all the location dimensions between the datum target areas , A1 and A2. X = _________________,…

A: Give all the location dimensions between the datum target areas , A1 and A2.X =0  ,  Y =74   ,   Z =…

Q: ExJA 20° straight-tooth bevel pinion having 14 teeth and a diametral pitch of 6 teeth/inch drives a…

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: The part below has a variety of features that are labeled as datum features. Assume all are primary…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: Based on Figure 3: draw the section view along the x-x cutting plane line.  i) Complete the section…

A: Please refer the following image for required sectional view of the given object. 1 Grid = 1 Unit

Q: 4) FIND EGNS FOR VEM DRAW VEM DIAGRAMS 0 200 kit 30

A:

Q: Draw the following graphic symbols (a) Total run-out (b) position tolerance (c) symmetry tolerance

A: Given: Draw the given graphic symbols.

Q: 10 10 Base plate. Figure out the three views of the above figure , sketch the arrangement in first…

A:

Q: mechanical design and drawing

A:

Q: Q3: Chose and mark a datum point on the given work-piece (shown in figure 1) and mark out the…

A:

Q: Two cylinders act right after one another. Each cylinder is metered, and some actions are slow, and…

A: Volume for each action:Cyl. A extends DE = 65 cubic inCyl. A retracts DR = 62 cubic inCyl. B extends…

Q: 15. On the produced part below, show a simple sketch on how the flatness on the part m verified and…

A: Flatness:- It is defined as the minimum distance between two planes within which all the points on…

Q: find principle following figure moments fa # the

A:

Q: Use the image below to do the following  i.  draw 3 positions on a piece of paper. ii.  Chose a…

A: Find three positions and corresponding distances based on the reference point.Alos find linear…

Q: A marksman fires a practice round from A toward a target B. If the target diameter is 200 mm and the…

A: Given Data The diameter of the target is: d=200 mm=0.2 m The distance between A to B is: x=1340 m…

Q: Generate isometric drawing from multiviews using drawing tools or free - hand. Use approximate…

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: Perform position analysis on the crank slider shown below by 1) labeling the unknown values on the…

A:

Q: Q3/ Draw the front section of the figure (2)? RIO p10 54 p82 $56 76 RI14 FROM ト!2 CENTRE OF BOSS $12…

A: Solution:   The front section of the figure is shown below:

Q: Given the top and front views, sketch the right face.

A: According to the details provided in the question. Top view and front view is given we need to draw…

Q: Q4. Draw a neat sketch to represent the following readings on scales of Vernier Caliper: 132.85 mm…

A: Given1) vernier scale reading  =132.85mm2) vernier scale reading =8.68mm

Q: SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE…

A: To mark the letters on the following figure mentioned.

Q: Ae bes elole 15.3 15.1 Ø0.3|A-B 6.40 6.35 9.55 9.50

A: (1) coaxially tolerance.on left diameter = ∅ 6.5-0.05+0.00on right diameter = ∅9.5-0.00+0.05 maximum…

Q: Analyse the codes below and work out the final position of the cutting tool. G90 G21; S600 M03; GO0…

A: It is required to determine final position of cutting tool

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.