the A light weight Parachute has a diameter of 7m and total wt. including Pay load is 1020N. The design terminal selling velocity of the Parachute is 5.5 m/see. A 1 in 12 -scale model of the Parachute is tested in wind tunnel with the same air in which the Parachute is moving, taking. Mair = 1.802 × 10³ 1) Calculate the Drag coefficient of the Parachute. ii) At what speed the wind tunnel be run ii) Aerodynamite drag on the model? , Pair = 1-225 kg/m³. okanter.com dynamic similarity.

the A light weight Parachute has a diameter of 7m and total wt. including Pay load is 1020N. The design terminal selling velocity of the Parachute is 5.5 m/see. A 1 in 12 -scale model of the Parachute is tested in wind tunnel with the same air in which the Parachute is moving, taking. Mair = 1.802 × 10³ 1) Calculate the Drag coefficient of the Parachute. ii) At what speed the wind tunnel be run ii) Aerodynamite drag on the model? , Pair = 1-225 kg/m³. okanter.com dynamic similarity.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.5 m filr Figure: Question 8 A 30kg uniform thin panel is placed in a truck with end A resting on a rough horizontal surface and end B supported by a smooth vertical surface. Knowing that the acceleration of truck is 4 m/s?, determine (a) the reactions at ends A and B, (b) the minimum required coefficient of static friction at end A.
Q2-3 [5 Points]:A fluid has an absolute viscosity of O.048 Pa-s and a specific gravity of 0.913. For flow of such a fluid over a solid flat surface, the velocity at a point 50 mm away from the surface is 0.694 m/s. Calculate the shear stresses at the solid boundary (N/m)
I- An open tank containi ng oil Cspar. = 0.80) is acceleratd verticaly at 8m/s". Determine the pressure 3m belar the surface if the notion is: a) upward with a positive acceleration. k) upward with negative acceleration. c) davnward with posi tive acceleration- di) dawnward with 'negative acceleration.
Compute the pressure @ point n ( Pn ) as shown by the differential manometer in KPa if pressure @ point m ( Pm ) is equal 1027.66 mm Hg. air plpeline where: a= 12" b=3,2 C-4.0 d- 12 m mercury density (16 300 kghm) water pipeline
View Policies Current Attempt in Progress The 669-N force is applied to the 112-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.72 HA=0.48 Answer: F= Save for Later i 40" N P = 669 N Attempts: 0 of 1 used Submit Answer
Exam Ql:- A steel cylinder floats on water, find the relative density of cylinder if the depth of submergence , h = 70 mm? 4cm Water Ed:8cm
DETERMINE Oo , Oc, YHB AND YHD. THE 15KN 5m 2m C 4m 5 m 10 KN >E 8 KN 5m EI CONSTANT
assume reaction time and coefficient of lateral friction.
20 of 25 Answer: AT = i A solid 0.67-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 23 in., its elastic modulus is E = 29000 ksi, and its coefficient of thermal expansion is a = 7.5 x 10-6 in./in./°F. Determine the temperature increase AT that will cause the rod to buckle. - /2 L -NM ||| B
28. The PCA rigid pavement design chart for a B-777-300 aircraft is shown in Figure 7.7.3 attached. What would be the required pavement thickness if the weight on the main landing gear is 627,700 lb, a modulus of subgrade reaction-300 psi/in, and a 28-concrete flexural strength=820 psi? The pavement is to be designed for a critical area and requires a safety factor-2.0. a. 6.0 inches b. 8.0 inches c. 14.0 inches 17.0 inches d.
Q- A semi-tubular cylinder of 75mm radius with concave side upstream (drag coefficient = 2.3) is submerged in flowing water of velocity 0.6m/s. If the cylinder is 7.2m long and density of water is 1000kg/m3, what is the drag?
TRIAL:1 Left Limb Reading (LL) = 22cm Right Limb Reading (RL) = 31.5cm ? Head Loss (H) CHECK