A solid 0.67-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 23 in., its elastic modulus is E = 29000 ksi, and its coefficient of thermal expansion is a = 7.5 x 10-6 in./in./°F. Determine the temperature increase AT that will cause the rod to buckle.

A solid 0.67-in.-diameter cold-rolled steel rod is pinned to fixed supports at A and B. The length of the rod is L = 23 in., its elastic modulus is E = 29000 ksi, and its coefficient of thermal expansion is a = 7.5 x 10-6 in./in./°F. Determine the temperature increase AT that will cause the rod to buckle.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

_Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C°) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 T1.2 195 3 35 Aluminium 300 18.9 4 30 90 Aluminium Steal 4m 2m
Situation 2 For the assembly shown, determine the stress in each of the two vertical rods if the temperature rises 40°C after the load P=50 KN is applied. Neglect the deformation and the mass of the horizontal bar AB. Compute the vertical movement under the load. Steel Aluminum E=200 GPa E=70 GPa L-4m A=300 mm? a-11.7x10*/°C L-3m A=900 mm a=23x10“ /°C 3 m 3 m 3 m Situation 3
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. Determine the maximum allowable value of P if the change in length of the bar is limited to 2 mm and the working stresses prescribed in the table are not to be exceeded. Material Properties Material Area(mm2) E (GPa) Normal Stress(MPa) Bronze 450 83 120 Aluminum 600 70 80 Steel 300 200 140 Aluminum 3P Bronze Steel 2P 4P - 0.6 m →- 1.0 m 0.8 m
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm A = 400mm? A- 200mm 40KN 10KN 20KN 1.5m 2.5m 2.0m Determine the change in length of steel rod having a length of 800mm and a diameter of 6.5mm. The rod is subjected to a force P equal to 110KN. Young's Modulus is 200GPA Compute normal strain of the rod
7 30 Enercise:- diameter of 12mm A cylindrical rod 100 mm long with is subjected to a 30000 N. Assuming that the tensile load of deformation is entirely elastic and allowable elevation in pligmeter is allowable reduction in dligmeter is 0.015mm. choose amory only meeting requirent U (Poiss ons vahu) 0.33 below Material Aluminium alloy Bronze Titanium allow manimum 0.3 mm while manimum E (GPa) 70 100 110 0.34 3
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the weight of the beam is 375 KN, determine the stress in the aluminum bar (in MPa). Bronze Bronze Alum Alum Bronze A in mm2 850 1500 E in Gpa 70 83 103.56 O 79.45 451.30 33.47
PROBLEM 2 A tri metallic bar is uniformly compressed by an axial force P-12KN applied through a rigid end plate The bar consists of a circular steel core surrounded by brass and copper tubes. The steel core has a diameter l0mm, the brass tube has an oute diameter of 15mm and the copper tube has an outer diameter of 20mm E for steel =210Gpa, E for brass = 100GPA and E for copper is 120GPA Calculate the compressive stress of each metal due to force P
CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Spronze = 80 MPa, find the maximum weight of the beam that the system can support (in KN). %3! Alum 850 Bronze A in mm2 1500 Bronze Bronze E in Gpa 70 83 Alum 291.408 O 211.932 437.393 O 90.673
A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If an axial load of F = 300 N and the cross sectional area of the rod is 200 mm2 , determine the stress in the section of copper. ... Сopper Steel 2F F 3m 2m A) 1.5 MPa В 0.75 MPa 3.0 MPа D 4.5 MPa
- An aluminum right-circular cylinder surrounds a steel cylinder as shown. The axial compressive load of 200 kN is applied through the rigid cover plate shown. If the aluminum cylinder is originally 0.25 mm longer than the steel before any load is applied, find the normal stress in each when the temperature has dropped 20 K and the entire load is acting. For steel take E = 200 GPa, a = 12 x 10-6/° C, and for aluminum assume E = 70 GPa, a = 25 x 10-6/° C. 200 kN Ans. ost = 9 MPa, oal = 15.5 MPa 80 mm- 85 mm- 141 mm. 500 mm
2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was attached, the rods' ends were leveled. If the rods' properties are as listed, find the maximum allowable value of M. (sw is the working stress). ow. 1.2m 1.2m 260mm 180mm Copper
1. A steel rod of 20 mm diameter passes centrally through a copper tube 40 mm external diameter and 30 mm internal diameter. The tube is closed at each end by rigid plates of negligible thickness. The nuts are tightened lightly home on the projected parts of the rod. If the temperature of the assembly is raised by 60°C, calculate the stresses developed in copper and steel. Take E for steel and copper as 200 GN/m² and 100 GN/m² and a for steel and copper as 12 x 10° per "C and 18 × 10° per °C. 200 A 108