Specify the required torque M on the power screw necessary to overcome a resistance of 490 N to motion of the carriage along it's horizontal ways. The screw has a mean diameter of 21mm and has two separate threads which move the carriage 16mm per revolution of the screw . The coefficient of friction may be taken as 0.15

Specify the required torque M on the power screw necessary to overcome a resistance of 490 N to motion of the carriage along it's horizontal ways. The screw has a mean diameter of 21mm and has two separate threads which move the carriage 16mm per revolution of the screw . The coefficient of friction may be taken as 0.15

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.58P: The screw of the carjack has a pitch of 0.1 in. and a mean radius of 0.175 in. Note that the ends of...

See similar textbooks

Similar questions

A double square thread power screw has a pitch of 6 mm and mean radius of 34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required to turn the screw.
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
The frictional coefficient has a value of 0.26795, and the normal force is 20kN. Determine the angle of friction.
An acme thread power screw that has a mean diameter of 25 mm and pitch of 5 mm is used to lift a load of 500 kg. If friction on threads is 0.1, determine the torque needed to turn the screw.
A square threaded power screw has an efficiency of 65% when raising the load. The coefficientof friction for the threads is 0.15, with the collar friction negligible. Determine the lead angle of thescrew.
An engine developing 40 hp at 1250 rpm is fitted with a cone clutch built into the flywheel. The con a face angle of 12.5 degrees and a mean diameter of 14 in. The coefficient of friction ta 0.20 and the n pressure on the clutch face is not to exceed 12 psl. Determine the required face width and the force m sary to engage the clutch, assuming uniform wear. Ans. 2.96 in.. 592 lb
1. A double square thread power screw has a pitch of 6 mm and mean radius of34 mm. If it is used to lift a load 50 kN and coefficient of friction of threads is 0.15, determine the torque required toturn the screw.A. 343.74 N-m B. 353.47 N-m C. 335.47 N-m D. 347.35 N-m2. A lubricated bolt needs an initial torque of 145 lb-ft to take the initial tension brought by the compressor withoutbreaking. Determine the initial torque needed by the bolt if the bolt was not lubricated.A. 107.85 lb-ft B.108.25 lb-ft C. 108.75 lb-ft D. 193.33 lb-ft
The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2150 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque required to drive the screw and the efficiency of the screw.
12. An ACME thread power screw has an efficiency of 70%. Determine the ratio of the lead to its mean diameter if the coefficient of friction of threads is 0.08 while the collar friction is found to be negligible.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
The following lead screw and saddle arrangement is used to lift aload of 550 kg. The square thread has a pitch of 3 mm and a diameter of 15 mm. The coefficient of friction is 0.2. Calculate the torque required to rotate the screw on raising and lowering.