In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2 .The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing

In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2 .The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
In a thrust bearing the external and the intermal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The totail axial load is 80 kN and the intensity of pressure is 350 kN/m. The shaft rotates at 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction, Also, find the mumber of collars required for the bearing
In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m?. The shaft rotates atę Op rpm. Taking the coefficient of friction as 0.os, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
An open belt connects two flat pulleys. The pulley diameters are 300 mm and 450 mm and the corresponding angles of lap is 160°. The smaller pulley runs at 200 r.p.m. the pulley are kept at a distance of 3500 mm. The coefficient of friction between the belt and pulley is 0.25. It is found that the belt transmits 3 kW . Calculate the tensions in tight and slack side and the length of the belt.
4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45, and a torque of 350 ft-lbs is to be transmitted, calculate the belt tensions.
A multiple V-belt drive is required to transmit 4 kW. The smaller pulley of the system is150 mm diameter, rotates at 200 rev/min, and has an angle of lap angle of 135°. Thegrove angle is 40° and the coefficient of friction between the belt and the pulleys is 0·3.If the maximum tension in any one belt is limited to 800 N, calculate:(a) The number of belts required. (b) The minimum tension in any one belt. (c) The required pre-tensioning of the belt. The centre-to-centre distance between the pulleys is 2 m.(d) Determine to the nearest mm, the required size for the larger pulley.(e) Find the approximate length of the belt
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
From the rotating shaft shown below, a force 100 N was pulled to reduce the shaft’s angular speed through its cables. What is the maximum cable tension if the shaft rotates in a counterclockwise direction? Use coefficient of friction on shaft equal to 0.2.
The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top dead centre. The stroke of the engine is 900 mm, the connecting rod is 1500 mm in length and the coefficient of friction for the lubricated crosshead guide is 0.025. Calculate EACH of the following: (a) the magnitude of the instantaneous torque; (b) the magnitude of the instantaneous force to overcome guide friction.
A drum requires a torque of 200 N.m. to get it to start rotating. The static of friction between the belt and the drum is 0.35. 1. Compute the value of T2 to cause impending slippage between belt and drum. 2. Compute the value of T1 to cause impending slippage between belt and drum. 3. Compute the minimum axial force at A on the drum required to create enough tension in the belt to start the rotation of the drum.
The axial pressure on a single disc clutch (both sides of the disc is effective) is limited to 0.12 Mpa. This is designed for a vehicle with 13kW power at a speed of 700 rpm. Assume uniform wear conditions and a friction coefficient of 0.25. If the outer dimater of the disc is 1.25 times the internal diameter, determine the dimensions of the disc lining and the axial force exerted by the springs.
A multiple disc clutch has three discs on the driving shaft and two on the driven shaft, providing four pairs of contact surfaces. The outer diameter of the contact surfaces is 250 mm and the inner diameter is 150 mm. Determine the maximum axial intensity of pressure between the discs for transmitting 18.75 kW at 500 r.p.m. Assume uniform wear and coefficient of friction as 0.3.