A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at bottom of the beamsection at midspan where the total losses of the prestressing force is 23% (MPa)Properties:Beam width = 285 mmBeam height = 475 mmUniform load = 9.1 kN/mSpan of the beam = 13 mPrestressing force 469 kNeccentricity = 104 mm%3D%3D%3D%3D

Given: Beam width, b = 285 mm Height, d =475 mm Uniform load = 9.1 kN/m Span, L = 13 m Prestressing…

Answered: simply supported beam is carrying a…

Engineering

Civil Engineering

simply supported beam is carrying a uniform load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Explain a bernullies beam with equation(s)

A: Bernoulli's beam, also known as the Euler-Bernoulli beam, is a concept in structural engineering…

Q: under the following boundary conditions (x = 0, y = 0); (x = L, y = yMax). what kind of beam is…

A: Beams can also be described with their boundary conditions. In the given question, When x=0…

Q: A beam carries a concentrated as shown in Fig. 60 MPa? Can a greater load be applied if the section…

A: Given : To find : 1 ) The safe value of W can be applied? 2 ) Can a greater load be applied if the…

Q: A W6x12 beam is strengthened with a % x ¾ inch bar welded to its top of the top flange on…

A: For W 6 x 12. D(depth) = 12" , Bf (width of flange)= 4", tw (web thickness) = 0.23", tf (flange…

Q: A simply supported beam carries a uniformly stributed load of (w) over the whole length, the ear…

Q: WHICH SECTION BEAM WILL BE STRONGER

Q: What is obtained when you multiply the relative stiffness to the sum of girder/column factor and…

A: Given details- Relative Stiffness multiplied by sum of girder/ column factor and carry over factor.

Q: If a wide-flanged beam fails in local buckling of the flange, will the top flange, the bottom…

A: When the beam section is subjected to large amount of stresses or loads, the thin sized members as…

Q: A cantilever cast-iron beam is 9 ft long and has a “T” cross section, as shown. Calculate the…

A: Given data Length of the beam is 9 ft. Load applied is 300 lb. The weight of beam is neglected.…

Q: snip

A: Given- DL=170lb/ft Roof live load=100 lb/ft S.L=280lb/ft W.L=180lb/ft Assume beam weight=40lb/ft

Q: Given: Consider the floor frame below supports a 6-in. concrete floor. Assume the beams and girders…

Q: 1. A 100mm x 200mm timber beam has a span of 4.0m and carries a uniform load of 15kN/m. including…

A: Given data, Span of beam, L = 4 m Uniform distributed load acting on the beam, w = 15 kN/m Depth of…

Q: A beam of T-section has I = 1000 cm4 and depth 10 cm. Flange of the section is in tension. If the…

Q: O . A

A: Which of the following is symmetric beam? option (b) is correct option

Q: H.W: Circular Column with Uniaxial Bending. Determine the reinforcement to be provided in a circular…

A: The given data is: Diameter, D=500mm Pu=1600KN Mu=125KN-m f'c=20 MPa fy=250 N/mm2

Q: A two span beam subjected to shear and flexure only is reinforced as follows: SECTION @ MIDSPAN @…

Q: A beam of T-section has I = 1000 cm4 and depth 10 cm. Flange of the section is in tension. If the…

Q: How much total reinforced concrete weight does Beam A support considering its self-weight and the…

Q: The allowable bending stress oallow = 24 ksi and the allowable shear stress of Tallow = 14 ksi.…

A: Given- σallow=24ksiτallow=14Ksi

Q: Please help! I need the answer immediately. A W14 × 74 flexural member of ASTM A992 steel is used as…

A: Given Data: W14 × 74

Q: Problem: Determine the design moment capacity of the rectangular beam with the following…

Q: Using AISC specification, calculate how much weight for the truss structure

Q: A howe truss has six panels and each panel is 1m. The span is 6m and height 1.50m. Joints U1, U2,…

Q: aminated wood beam consists of eight 2.25 in. × 5.25-in. planks glued together to form a section b =…

A: Maximum shear force is τmax≥VmaxQItQ=5.25×9×92I=5.25×18312so,V≤1105.25×183125.255.25×9×92V=6930lb

Q: A laminated wood beam consists of eight 1.75 in. x 5.50-in. planks glued together to form a section…

A: To find out the moment of inertia about Z axis.

Q: A beam of T-section has I = 1000 cm4 and depth 10 cm. Flange of the section is in tension. If the…

Q: flexure only is reinforced as follows: Given: Stirrup diameter, ds = 10 mm Concrete f'c = 21 MPa…

Q: A doubly reinforced beam, which have a base of 310 mm, and an effective depth of 410 mm, is…

A: Balanced steel Ratio PBalanced is corresponding to amount of steel at which concrete failure and…

Q: Determine the ultimate moment capacity of a reinforced concrete T-beam A as shown. The beams are…

A: Calculation: Given: Span = 12m fc = 21 MPa fy = 414 MPa bw = 300 mm h = 475 mm slab thickness, t =…

Q: P = L1 = L2= L1 Your Answer: P 195 2.50 4.5 Answer KN m m L2 ▷ View hint for Question 1 P The…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Q: .Why in the majority of cases the suspended span of the beam is relatively long?

A: Suspended span is basically the span which is not supported and it is hung between the two supports.…

Q: Problem 1. Method of Section in Trusses A bridge walkway shown has 80 kN loads acting on B,D,F, and…

A: Determine the force in member CE using method of sections.

Q: Determine the forces in members CD, CJ, and DJ. M 10' L B 6 panels at 4' K C D I E H F G L LL LL L

Q: reinforcing steel area (As)

A: The relationship between the ultimate moment capacity (Mu) and Area of the reinforcing steel is to…

Q: Please answwer the question in the picture, Show all of your work please.

A: Follow the steps...Image_1Image_2Image_3As calculated above Absolute Maximum SF =17 kipAbsolute…

Q: What will be the live load for which roof truss should be designed when pitch of roof truss is 16°…

A: given pitch of roof truss=16ono access is provided to the roof

Q: Q# Analyze the beam for stresses at point A and B due to combined effect of loading. Force F is…

A: the given beam is simply supported determinate beam this can be analyze by the equation of the…

Q: 1.A reinforced concrete beam has a width of 300mm and an éffective depth to tension bars of 600mm.…

A: We have to determine the tension steel area if the beam is to resist an ultimate moment of 650 KN.m…

Q: cion #1: A hollow trapezoidal steel structural section, filled with concrete, has outside and inside…

Q: Assuming k = 3000 lb/in², and considering only the bending stress: What rail type would you…

A: Given, Track modulus (k) = 3000 psi Force (P) = 30000 lb

Q: The timber member has a cross-sectional area of 1700 mm2 and its modulus of elasticity is 12 GPa.…

Question

A simply supported beam is carrying a uniform load. If the beam properties are given below, what is the final stress at bottom of the beam
section at midspan where the total losses of the prestressing force is 23% (MPa)
Properties:
Beam width = 285 mm
Beam height = 475 mm
Uniform load = 9.1 kN/m
Span of the beam = 13 m
Prestressing force 469 kN
eccentricity = 104 mm
%3D
%3D
%3D
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A reinforced concrete T-beam contains 1.25x10 m² of steel reinforcement on the tension side. If the steel stress is limited to 115 MN/m² and the concrete stress to 6.5 MN/m², estimate the permissible bending moment. The modular ratio is 15. 30 cm- 12 (0.30-m -60 cm- 10cm -000-1.25 x 10³m² 15cm
Design Shear ReinForcement For a beam Shown below. It's Size is 350 x 600· It's effective depth is 525mm. It is Supported
How could I find what the maximum evenly distributed load, that the beam can safely support?
Design the shear reinforcement of the beam loaded as shown using USD with fc’ = 20.7 MPa and fy = 276 MPa
steel joist is spaced at 3’-0” oc and spans 35’-0”. It carries a dead load of 45 psf and a live load of 100 psf. What is the most economical steel joist able to carry this load? a. 24K7 b. 26K7 c. 28K7 d. 30K7
Estimate the loads applied on the Beam 1, including the load transferred from Slabs 1 and 2 (self-weight of slabs), the self-weight of Beam 1 and the water tank load. Note that the water tank load may be idealised as a point load. Please also note that there are also other types of loads, which should be considered for practical design, but for simplicity they are not considered here.
The answer is between 18.25 and 20.25
parts A & B are not related to this part of question
For the following plan it is required to: 1- Design all beams for flexure and shear, where they have additional 30 kN/m distributed factored load 2- Design the columns. The concrete has a strength of 30 MPa, and the yield strength of the steel is 420 MPa. Show full calculations and neat sketches. All dimensions are in m. I 03 B2 0,3 7 B1 Wu=20 kN/m2 B1
The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?
Find the maximum tensile and compressive flexural stresses for the cantilever beam with loading and cross section shown below
A beam of rectangular cross-section is subjected to a vertical shear force 'V. The shear force carried by the upper 1/3rd of the cross-section is