cion #1: A hollow trapezoidal steel structural section, filled with concrete, has outside and inside dimensions as shown in the figure below. Thickness of the trapezoidal steel is 5 mm throughout its perimeter. The section is 3m high and supports a compressive load of 350 kN. Es 200 GPa and Ec = 20 GPa. Find o, oc and 8. 350kN 110mm 120mm

cion #1: A hollow trapezoidal steel structural section, filled with concrete, has outside and inside dimensions as shown in the figure below. Thickness of the trapezoidal steel is 5 mm throughout its perimeter. The section is 3m high and supports a compressive load of 350 kN. Es 200 GPa and Ec = 20 GPa. Find o, oc and 8. 350kN 110mm 120mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

b) The floor system shown is subjected to a total uniform distributed load of 20 kN/m². Sketch the loading that acts along the members and CDE. 2 m E 3 m F G H 4 m 3 m
Compressive force AO is 4509 kN. Distances are; a=7.09m, b=2.11m, c=5.98m, d=3.99m, e=7.01m, f=5.00m, h=10.02m 1. Force in wire AB. Tension or compression? 2. Force in wire AC. Tension or compression? 3. Force in wire AD. Tension or compression?
Determine the design ultimate moment of resistance of the following beam : Prestressing tendons Section Properties = 1860 N/nmm2 213000 mm2 A. I = 13.19 x 10° mm4 1.15 = 195 kN/mm² 325 mm Am = 845 mm2 d = 700 mim 400 P. 880 kN b, = 400 mim 200 mm 200 Concrete 150 mm 1 = 40 N/mm2 750 150 1.5 Ec = 28.0 kN/mm2 200
2. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in members EF, AF, and BF.
4 in. 200 kip 3 ft - The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. If the column is subjected to an axial force of 200 kip, determine the average normal stress in the concrete and in each rod. Each rod has a diameter of 1 in - change the applied force of 200 kip to 185.7 kip - change original diameter of each steel rod of 1 in to 1.35 in
Problem Set 3: The overhanging beam carries a uniformly distributed load totaling 8W and two concentrated loads of magnitude W each. Determine the safe value of W if the working stresses are 3 000 psi in tension and 10 000 psi in compression. W 8W W Lam AV BV V VC 1 in 12 in 4ft 16ft 4ft D 8 in 1 in
Consider the two sections with their indicated properties below to answer the following: 8-36 Ø 1000 mm Section 1 f'c fy stirrups CC 32 415 10 50 800 mm 700 mm 400 mm Section 2 f'c fy stirrups CC 600 mm rebar 21 415 10 40 32 100 mm Calculate the depth of the neutral axis of section 1 in mm. Calculate the depth of compression block of section 1 in mm. Calculate the reinforcement stress of section 1 in MPa.
Question 4) Check the maximum permissible A, to ensure ductile behavior. Compute the design moment strength øMn. Use fy = 60000 psi and f = 4000 psi. %3D -6 in.- 3 in. 2 #9 6 in. 12 in, 30 in. 6 in. 5 #11 3 in. 3 in. +4 @ 3 in. = 12 in. +3 in. 18 in.-
Determine the force of member BD. Include a negative sign if the answer is in compression. Indicate whether it is in tension (T) or in compression (C) in your solution. T-m- 40 kN Dt 60 kN 40 kN 3 m 7m A Az 3 m Ax Cy Plan AAA, 4 m
"D.35. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 25.8 MPa, fy= 506.8 MPa, bf= 710 mm, t= 90 mm, hw= 470 mm, bw = 440 mm ds= 10 mm, ct- 30 mm, cb = 35 mm. Steel bar details: compression side at top (single layer): 4- 16 mm dia. , tension side (double- layered): upper layer is 4 - 28 mm dia. and lower layer is 5 - 28 mm dia." Use the editor to format your answer br ... Ct Bar diameters and positioning in the figure given are just representations. Refer to the problem statement for the ds hw number of bars and bar diameters to use in your computation. 25 mm Cb bw
From the given figure below, determine the maximum flexural stress of the beam if it has a cross section of 150mm wide by 250mm deep. (JN 10 N/m o' RA=42N 42N 3M B IM 75Nm 81NM Im RD=3N -3N 0° 78 Nm 3NM V-DIAG M-DIAG
7. 20 ft I KLF Mmax A max =