A laminated wood beam consists of eight 1.75 in. x 5.50-in. planks glued together to form a section b = 5.50 in. wide by d = 14 in. deep, as shown. If the allowable strength of the glue in shear is 130 psi, determine (a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 25 ft. (b) the shear stress in the glue joint at H, which is located 3.5 in. above the bottom of the beam and at a distance of x = 72 in. from the left support. Assume that the beam is subjected to the load w determined in part (a). (c) the maximum tension bending stress in the beam when the load of part (a) is applied. 1 (tуp.) H L Determine the moment of inertia for the cross-section about the z centroidal axis. Answer: I, = i in.4

A laminated wood beam consists of eight 1.75 in. x 5.50-in. planks glued together to form a section b = 5.50 in. wide by d = 14 in. deep, as shown. If the allowable strength of the glue in shear is 130 psi, determine (a) the maximum uniformly distributed load w that can be applied over the full length of the beam if the beam is simply supported and has a span of L = 25 ft. (b) the shear stress in the glue joint at H, which is located 3.5 in. above the bottom of the beam and at a distance of x = 72 in. from the left support. Assume that the beam is subjected to the load w determined in part (a). (c) the maximum tension bending stress in the beam when the load of part (a) is applied. 1 (tуp.) H L Determine the moment of inertia for the cross-section about the z centroidal axis. Answer: I, = i in.4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

DETERMINE THE MOMENT OF INERTIA OF THE BUILT-UP SECTION ABOUT THE INDICATED X. AXIS. The thickness of the stem in problem 2 is 1.5". Please show clear and complete solution in tabulated form. Thank you
30" Design the reinforcement for the T-beam in the middle which carries a live load of 200 lb/ft². The length of the beam is 25 ft. In your design assume concrete with a compressive strength of 3,000 psi density 150 lb/ft³ and Grade 60 Steel. 27" 12" 10'-0" 12" 10'-0" 12"
Problem: Using WSD & USD, design the midspan reinforcement of stringer (B-3) for the second floor of a 3-storey residential building shown below. Use 20.7MPa compressive strength of concrete @ 28-days and grade 40 reinforcing bars. Use Ye= 24.5 KN/m³. Design the stringer as rectangular beam. Assume simply supported. 450mm 250mm 250mm 450mm, Superimposed Deadloads = 2.70 KPa Stirrups = 10mmo Main bar = 25mm 350mm B-4 STAIRWELL B-1 250x400mm S-3 B-3 250x400mm S-4 (3000) mm 350mm B-4 350mml Stringer Section (2000) mm (3500) mm (2000) mm 700mm
Combined Stresses Given Hollow Steel Section (HSS) that is 4"x6" and 1/2" thick, with axial and transverse loading shown, determine the total normal stress at a. The 5k load on the bottom of the beam b. At the mid-span in the middle of the beam C. At the 10k load on top of the beam 5k 10k A 5' 10' 5' B CENTROID 4" 5 k 3k 8k 6" 2' 6.25k 8.75k +6.25k SECTION +1.25k 'V" -8.75k +43.75k-ft. +31.25k-ft. 'M' 8k 5 k + tension P = Ok %3D
#2 will upvote anyone who will answer correctly. Thanks
7-35. The boards are glued together to form the built-up beam. If the wood has an allowable shear stress of 7allow 3 MPa, and the glue seam at D can withstand a maximum shear stress of 1.5 MPa, determine the maximum allowable shear V that can be developed in the beam. 50 mm 50 mm 50 mm 50 mm D 150 mm 50 mm B 150 mm Probs. 7-34/35
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
For a composite section attached, derive the equation for Y-bar assuming that the PNA is located in the flange of the steel beam. Hint: Balance the resultant forces through the section. Recall that Y-bar is the distance from the top of the steel flange to the PNA for any location with the PNA below the top of the steel flange.
A laminated beam is composed of four (4) planks, each of 150 mm x 30 mm, glued together to form a section 150 mm x 150 mm. The allowable shear stress in the glue is 850 kPa, the allowable shear stress in the wood is 1050 KPA, and the allowable flexure stress in the wood is 10 MPa. Determine the maximum uniformly distributed load which can be carried by the beam on a 45 m simple span.
Please answer as soon as possible
Required information A composite beam is made by attaching the timber and steel portions shown with bolts of 12-mm diameter spaced longitudinally every 200 mm. The modulus of elasticity is 10 GPa for the wood and 200 GPa for the steel. The vertical shear is 4.4 kN. 12 mm 250 mm 12 mm 150 mm- Determine the average shearing stress in the bolts. (Round the final answers to two decimal places.) The average shearing stress in the bolts is MPa.
Asiacell lln. H.W. No.1 For the simply supported solid one way reinforced concrete slab shown in the figure below having a span of (L= 4m), check the following requirements using strength method: a- Slab thickness b- The spacing between reinforcement for main and shrinkage reinforcement c- The actual reinforcement with minimum reinforcement d- Calculate ultimate resisted moment that can be withstand by the slab e- Determine the ultimate uniformly distributed load carried by slab. f = 25 N/mm2 fy=420 N/mm² + 10mm@s00mm shrinkage h=200mm -L=4m- $12mm@200mm main