Show the typical Stress versus Strain curve for the following materials, and define the materials properties The stress-strain curve can be used to read off the structural load ability of materials. For many materials, ncluding metals, their loading bearing capability is one of the most important material properties". by reference to the diagram:

Show the typical Stress versus Strain curve for the following materials, and define the materials properties The stress-strain curve can be used to read off the structural load ability of materials. For many materials, ncluding metals, their loading bearing capability is one of the most important material properties". by reference to the diagram:

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.5P

See similar textbooks

Similar questions

Strain = 600 Stress = Strain = 500 Stress = 400 500 300 400 300 200 200 100 100 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain Stress (MPa)
A circular bar of magnesium alloy is 750mm long. The stress-strain diagram for the material is shown in the figure. The bar is loaded in tension to an elongation of 6.0mm, and then the load is removed. (a)What is the permanent set of the bar? (b)If the bar is reloaded, what is the proportional limit? (High: Use the concepts illustrated in figures below)
A steel alloy specimen having a rectangular cross section of dimensions 19.1 mm x 3.1 mm (0.7520 in. × 0.1220 in.) has the stress-strain behavior shown in the Animated Figure 6.22b. If this specimen is subjected to a tensile force of 98290 N (22100 Ib;) then (a) Determine the amount of elastic strain induced. (b) Determine the amount of plastic strain induced. (c) If its original length is 610 mm, what will be its final length after this force is applied and then released? The elastic modulus for steel is 207 GPa. (a) i (b) i (c) i mm
Below is the stress-strain curves of four different materials (A, B, C, and D). Make a brief interpretation of each curve, and rank the materials based on its rigidity. R E STRAIN
Fatigue strength for non- ferrous materials in defined at stress cycles 10^3 10^5 10^7 10^9
Figure P1.16 shows the stress–strain relations of metals A and B during tension tests until fracture. Determine the following for the two metals (show all calculations and units): Proportional limit Yield stress at an offset strain of 0.002 in./in. Ultimate strength Modulus of resilience Toughness Which metal is more ductile? Why?
The stress-strain curve for a metal is plotted as shown in Figure Q1 (a). On the graph,show the yield point, fracture point, proportional limit and ultimate point
Consider a cylindrical specimen of a steel alloy (Please see the figure) 0.33 in. in diameter and 3.15 inches long that is pulled in tension. given:-Elongation is 0.018 in-Tensile stress = 200 ksi -Tensile strain = 6.83*10^-3 -Ultimate stress = 281.82 ksi -Ultimate strain = 0.05solve: Fracture point (stress and strain values)
The state of stress on an element in plane stress is shown as in the figure. 150 N/mm What is the value of o if the values of the principal stresses are 164 N/mm² and 36 N/mm², both tensile?
A material has the stress–strain behavior shown in Figure What is the material strength at rupture? What is the toughness of this material?
A bar of length 2.0m is made of a structural steel having the stress-strain diagram shown in the figure. The yield stress of the steel is 250 MPa and the slope of the initial linear part of the stress-strain curve (modulus of elasticity) is 200GPa. The bar is loadded axially until it elongates 6.5mm, and then the load is removed. How does the final length of the bar compare with its original length? (Hint: Use the concepts illustrated in figure below)
An element in plane stress is subjected to stresses o, = -8400 psi, ay = 1100 psi, and ty = 1700 psi (see figure). The material is aluminum with %3D modulus of elasticity E =10,000 ksi and Poisson's ratio v = 0.33. Determine the following quantities: (a) the strains for an element oriented at an angle 30 degrees, (b) the principal strains, and (c) the maximum shear strains. Show the results on sketches of properly oriented elements. Ty Txy Ox