View Policies Show Attempt History Current Attempt in Progress The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the strain components En Et and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle 8. Sketch the deformed shape of the element. Ex = -1100 μe, ey - 490 μE, Yxy = 1500 prad, and 8 = 34° Answer: En = Et = Ynt = Save for Later 0 με με urad D Attempts: 1 of 3 used Submit Answer

View Policies Show Attempt History Current Attempt in Progress The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain. Determine the strain components En Et and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle 8. Sketch the deformed shape of the element. Ex = -1100 μe, ey - 490 μE, Yxy = 1500 prad, and 8 = 34° Answer: En = Et = Ynt = Save for Later 0 με με urad D Attempts: 1 of 3 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

/
The rectangular plate is subjected to force P that causes elongation in the horizontal direction and shrinking in the vertical direction as shown with the dashed line in the figure. Assume a = 550 mm, Δx = 2 mm, and Δy = 1.1 mm. Determine the shear strain γxy at point A?in micro rad Determine the shear strain γnt at point A?in micro rad What is the normal strain in the x-direction?micro£
Thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the figure.[a = 200 mm, b = 202.1 mm, c = 198.9 mm] For the deformed plate, determine the normal strain of diagonal PR? In micro £ For the deformed plate, determine the shear strain xy at corner P?in micro rad
Figure Q4 shows a piece of triangular thin plate ABC with thickness 5 mm. A linear pressure as shown in the figure is being applied to edge AB with maximum intensity of 100 kN/m² at the middle of edge AB. The plate is made from stainless steel, with a Young's modulus of 200 GPa and Poisson's ratio of 0.3. The deformations in the plate are to be obtained. For such purposes, the finite element method is being employed. (a) (b) (c) (d) (e) State the type of problem involved in this case (to determine the stiffness matrix to be used). Model this problem optimally using the least number of orthogonal triangular elements only. Label the nodes and elements and indicate clearly the status of all the relevant degrees-of- freedom in this model. Set up the appropriate system of simultaneous equations and solve for the unknown displacements. Displacements at point T. Without any calculation, explain on the value of strain at points S and T.
ASAP
Please Help me
The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain. Determine the strain components En, Et, and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle O. Sketch the deformed shape of the element. Ex = -850 UE, Ey = 310 UE, Vxy = 1050 urad, and 0 = 39°.
The strain components EE. and Vxy are given for a point in a body subjected to plane strain. Determine the strain components En. Et and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle 8. Sketch the deformed shape of the element. Ex=-1150 μe, &, = 290 μE. Vxy = 1450 μrad, and 8 = 38° 12 X Answer: {= Ynt = με με urad
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the strain components εn, εt, and γnt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle θ. Sketch the deformed shape of the element. εx = -1200 με, εy = 240 με, γxy = 1350 μrad, and θ = 36°.
Schematically find the normal and shear stresses in the plane when the element given in the form of plane stress is rotated 30 degrees clockwise with the Mohr circle.
Use stress transformation method and not the equations.
At a point on the free surface of a machine component the strain rosette shown in the figure below