Required information.NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.Consider the given network, where Vx=0,7 V.7502ww220 2www.45 (20 00V₂1220 03A-Use your equivalent circuit to determine the power delivered to a 100 resistor connected to the open terminals. (You must providean answer before moving on to the next part.)The power delivered to the 100 Q2 resistor ismW.

In this question, we need power delivered to the 100 ohm resistor. Power P = = I2R Watt

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given network, where Vx=0,7 V. 45 V₂ 22002 7502 www 122003A Use your equivalent circuit to determine the power delivered to a 100 Q resistor connected to the open terminals. (You must provide an answer before moving on to the next part.) The power delivered to the 100 2 resistor is mW.

Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Consider the given network, where Vx=0,7 V. 45 V₂ 22002 7502 www 122003A Use your equivalent circuit to determine the power delivered to a 100 Q resistor connected to the open terminals. (You must provide an answer before moving on to the next part.) The power delivered to the 100 2 resistor is mW.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l33.2AI4RT3.582R116R210R3R420PTP1P2P3P4
How do I find the total Ohm's of this in steps? been on it forever now.
Determine the total resistance, Rī, and current, I, for the circuit in Figure Q1(b). 30V- RT 50Ω 2002 4092 7092 m Figure Q1(b) 3002 m 6092 [Answer: 22.430, 1.34A]
Step 5: Calculate the voltage across resistor R6 (VR6) [mV]. Use the resistance values from step 3 as follow R5 = 211.51ohm andR6 = 1420.86ohm. For the calculation of VR5 close Switch 1 and leave Switch 2 open. For the calculation of VR6 close Switch 2 and leave Switch 1 open. Use the circuit diagram of figure 1. Step 6: Calculate the maximum power absorbed by resistor R5 (PR5)[μW] and the maximum power absorbed by resistor R6 (PR6) [μW]. Use the resistance values from step 3 as follow R5= RTh(a,b) and R6 = RTh(b,c). Vs = 1.5V R1 = 4700ohm R2 = 2200ohm R3 = 6800ohm R4 = 2700ohm VR2 = 0.253V VR4 = 0.311V VR5 = 254mV
4.-For-labeled currents, draw an arrow to show the direction of the actual positive current. For labeled voltages, circle the node that is at the actual highest potential. Note that the positive and negative signs of the voltage represent the polarity of the probes of a voltmeter connected to the device. The value shown is the reading on the voltmeter. (segment of wire) 2A -2A -5A 2.de 3A TA Cov E 5V 12V + 3V -10V -201
Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a switch. The switch is placed in position A at time t = 0 and switched to position B at time t = 743 ms. Find the voltage across each of the resistors at time t = 1.17 seconds. Owo DO A R R in in ete SW éte لفظو
INSTRUCTIONS: Solve the following problems. Show and COMPLETE solutions. Draw all CIRCUIT DIAGRAMS or the equivalent circuit (dummy circuit) as the case may be. Write your solutions on sheet/s of short bond paper. A battery is to consist of 20 identical cells. The emf of each cell is 1.5 V and the internal resistance is 0.20 ohm. This battery will be used to supply power to a 10 ohm lamp. Determine the current on the lamp if:1. The 20 cells are connected in series 2. The 20 cells are connected in parallel 3. The 20 cells are arranged 5 cells in series in 4 parallel rows.
subject:Circuits 1please this one too give me a slightly favor can you answer this questions please wanna learn more im having difficuilty about this questions
150 100 + VA- a -4V AVA -7V 81. B b Figure 2 shows a simplified model of a gas-discharge lamp. One characteristic of these lamps is that they exhibit negative resistance; in other words, as current increases the voltage drops further, making such lamps inherently unstable. As such, a current-limiting ballast is required. For the connection shown in the figure: 1. Find the equivalent Thevenin circuit of the lamp. 2. Find the ballast resistance needed to limit the current drawn from a 24-volt source to 6 amperes.
Estimate voltage E2 when E1=90sin2400t V, R1=R2=20 ohms, L1= L2=3mH and M=0.15mH
Two resistive coils R1, R2 are connected in parallel across 130 V DC supply and takes 13 A from the supply. The power dissipated in R1 is 610 W, then the value of resistive coil R1 is
A circuit component carries a current of 2.4 amperes and has a voltage drop of 10 volts across it. What is the resistance R of the component? Round your answer to two significant figures. R = Number S2