A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816

A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

A certain unfiltered center-tapped full wave rectifier is powered by a 120 Vrms, 60 Hz power system. The peak value of the output voltage under loaded conditions is 30 V. The capacitance value is 2000 uF, load current of 2A, determine the following: 4. DC load voltage Ripple factor C.
A three phase fullwave controlled rectifier has an input voltage which is 480vrmsat 60hz. the load modelled as a series resistance and inductance with R=10ohm and l=50mH. determine the delay angle to produce an average of 50ain the load.
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
Q-2: A singie phase fiull-wave controlled rectifier is connected to RL load (R-15 ohm and 1.-20mH ). Vs- 240 and 50 Hz supply When the firing angle is a=55. Deternine: A} the average voltage and average current in the load. B) The form factor and ripple factor. C) Peak inverse voltage of the thyristor.
Calculate the rms load current for the single phase uncontrolled half-wave rectifier when the source voltage of 200V at a frequency of 50Hz, and load resistance is 10ohm.
One component that does not need to be installed in the correct orientation is a: a. Resistorb. Diodec. Voltage regulatord.
A single-phase center-tapped rectifier has an R-L of R= 20 0, L = 50mH, and a 240 V ac 50 Hz source voltage. Determine: i. The average and rms currents of the diodes and the load. ii. The rms and average 50 Hz source currents. iii. The power absorbed by the load. iv. The supply power factor.