Need help I’m confused Required informationAccording to potential theory for the flow approaching a rounded two-dimensional body, as in the figure below, thevelocity approaching the stagnation point is given by u= U(1-.upstream.atix), where a is the nose radius and Uis the velocity farStagnationpoint(u = 0)yaEvaluate the maximum viscous normal stress if the fluid is SAE 30 oil at 20°C, with U = 17 m/s and a = 11 cm. For SAE 30 oil, p = 917kg/m and u = 0.29 kg/(m-s).Pa.The maximum viscous normal stress is

Given: The speed, U = 17 m/s The constant, a = 11 cm The density of fluid, ρ = 917 kg/m^3 The…

Required information According to potential theory for the flow approaching a rounded two-dimensional body, as in the figure below, the velocity approaching the stagnation point is given by u= U(1– atix), where a is the nose radius and U is the velocity far upstream. Stagnation point (u = 0) a Evaluate the maximum viscous normal stress if the fluid is SAE 30 oil at 20°C, with U = 17 m/s and a = 11 cm. For SAE 30 oil, p = 917 kg/m3 and u = 0.29 kg/(m-s). Pa. The maximum viscous normal stress is

Required information According to potential theory for the flow approaching a rounded two-dimensional body, as in the figure below, the velocity approaching the stagnation point is given by u= U(1– atix), where a is the nose radius and U is the velocity far upstream. Stagnation point (u = 0) a Evaluate the maximum viscous normal stress if the fluid is SAE 30 oil at 20°C, with U = 17 m/s and a = 11 cm. For SAE 30 oil, p = 917 kg/m3 and u = 0.29 kg/(m-s). Pa. The maximum viscous normal stress is

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following rheological data were collected on a new "Thick 'n Spicy" brand of tomato catsup at 20°C and 90 kPa. rate of shear (s') shear stress (Pa) 10.0 20.4 20.0 21.5 40.0 23.0 60.0 25.0 80.0 26.5 (a) Plot these measured values on graph-paper. Which class of fluid does the catsup belong to? (b) Write the appropriate model for describing the rheological behavior of "Thick 'n Spicy" catsup. Specify the numerical value(s) and the units of the associated constant(s). (c) What shear stress is expected when the rate of shear, under vigorous shaking of a bottle of "Thick 'n Spicy", is 150 s?
The following rheological data were collected on a new "Thick 'n Spicy" brand of tomato catsup at 20°C and 90 kPa. rate of shear (s") shear stress (Pa) 10.0 20.4 20.0 21.5 40.0 23.0 60.0 25.0 80.0 26.5 (a) Plot these measured values on graph-paper. Which class of fluid does the catsup belong to?
(2) Referring to the following figure, the distance between plates is Ay = 0.5 cm, Av, 10 cm/s, and the fluid is ethanol at 273 K having a viscosity of 1.77cp (0.0177 g/cm s). dv:| ay (a) Calculate the shear stress Tyz and the velocity gradient of shear rate using cgs units. (b) (c) Repeat using SI units. Ay F, force Fluid shear between two parallel plates.
Compute the b Am? when the lower plate Steady skte momentum Flex Ey> momentum Ilex ty Velscity v in the Figure beloo is 0.804n/s s the pasitive X-directan, the Separation Y s o 304mm, md the fluid viscosity N is o7cP Naly) Longe t Final uelociny distribution in teady Flow
Two immiscible liquids of equal thickness h are beingsheared between a fixed and a moving plate, as in Fig. .Gravity is neglected, and there is no variation with x . Findan expression for ( a ) the velocity at the interface and ( b ) theshear stress in each fluid. Assume steady laminar flow.
This problem involves a cylinder falling Inside a pipe that is filled with oil, is depleted in the figure. The small space between the cylinder and the pipe is labricated with an oll film that has aboolute viscosity j. (a) Derive a formula for the steady rate of descent of a cylinder with weight W, diameter d. and length sliding inside a vertical smooth pipe that has inside diameter D. Aesume that the cylinder is concentric with the pipe as it falls. (b) Use the general formula you derive to find the rate of descent of a cylinder 100mm in diameter that slide inside a 100.5mm diameter pipe. The cylinder is 200mm long and weighs 15N. The lubricant is SAE 2OW oll with a viscosity of 2.0 x 10- Pax.
The velocity field for a line vortex in the r?-plane is given byur = 0 u? = K / rwhere K is the line vortex strength. For the case with K = 1.5 m/s2, plot a contour plot of velocity magnitude (speed). Specifically, draw curves of constant speed V = 0.5, 1.0, 1.5, 2.0, and 2.5 m/s. Be sure to label these speeds on your plot.
1. A fluid is bounded by two parallel plates of infinite width and length as shown in FIGURE Q1. The upper plate moves at 7 m/s, and the lower plate is fixed. The fluid's dynamic viscosity is 1.85X105 N.s/m?. Assume Couette flow with pressure gradient, = 0.1 N/m³. a. Propose the discretization method to solve Couette flow equation with pressure gradient below. Let the number of nodes, n = 9, the distance between the nodes is 0.05 m. Obtain the velocity of all the internal nodes using the matrix inversion method and the iterative method. Compare the results and the effectiveness of both methods (in terms of calculation effort and ease of setting up the problem). + b. Flow shear stress is governed by the following equation ôu Propose the discretization method to solve the above equation and calculate the shear stress at node 1. Describe the condition in tems of the pressure gradient when the shear stress at the bottom plate is zero. Moving plate at Um/s N= N-1 `Fixed plate FIGURE Q1
1) The velocity profile of a viscus fluid over a plate is parabolie with vertex 25 em from the plate ,where the velocity 125 cm/s. calculate the velocity gradient and shear stress at distance of (0, 5, 15 and 25 cm) from the plate given the viscosity of the fluid =7 poise ? Also draw the figure explain the relationship between the velocity gradient and shear stress. Take velocity profile for parabolic equation, (v = ay + by + c)
Find the velocity in the center, and velocity profile for giving system : p = 1000| kg/m' , µ= 0.03 *10* pa. , ū = 0.92 m/s , d= 0.28 m ? (Hi expertises this question is from Mechanical fluid.) I need answer quickly.
Consider steady, incompressible, laminar, fully developed, planar Poiseuille flow between two parallel, horizontal plates (velocity and pressure profiles are shown in Fig. At some horizontal location x = x1, the pressure varies linearly with vertical distance z, as sketched. Choose an appropriate datum plane (z = 0), sketch the profile of modi fied pressure all along the vertical slice, and shade in the region representing the hydrostatic pressure component. Discuss.
An incompressible viscous liquid (with density p and dynamic viscosity u) slides down an inclined plane as seen in the figure. The film thickness is h, and the solid substrate moves with a speed U up the incline. Assume steady, fully developed, laminar flow in the x direction with no pressure gradient (in the x direction). Furthermore, assume that the atmosphere at y = h imposes no shear stress on the liquid. (a) tions in terms of the parameters given. Derive an expression for the velocity profile using the Navier-Stokes equa- pgh? sin 0 4µ (b) If the magnitude of the substrate velocity is given as U determine the y-coordinate, normalized by the thickness, where the velocity is zero, i.e. find y/h for u(y) = 0. (c) reference line, assuming the substrate velocity given in part (b). Draw a qualitative sketch of the velocity profile, including a zero-velocity U Patm 19