Consider the toggle clamp shown in (Figure 1). Figure 235 mm- 30 mm 30 mm, 70 mm 20² 1 of 1 30 275 mm E > If a clamping force of 350 N is required at A, determine the magnitude of force F that must be applied to the handle of the toggle clamp. Express your answer to three significant figures and include the appropriate units. MA F-1370 1 X Incorrect; Try Again Provide Feedback N Submit Previous Answers Request Answer C ? Next >

Consider the toggle clamp shown in (Figure 1). Figure 235 mm- 30 mm 30 mm, 70 mm 20² 1 of 1 30 275 mm E > If a clamping force of 350 N is required at A, determine the magnitude of force F that must be applied to the handle of the toggle clamp. Express your answer to three significant figures and include the appropriate units. MA F-1370 1 X Incorrect; Try Again Provide Feedback N Submit Previous Answers Request Answer C ? Next >

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.31P

See similar textbooks

Similar questions

The couple moment acting on the pipe has a magnitude of 180 Nm (Figure 1). Figure -F A -150 mm. 150 mm B F 200 mm 600 mm 1 of 1 Part A Determine the magnitude F of the forces applied to the wrenches. Express your answer to three significant figures and include the appropriate units. F = Submit 0 μĂ Value Request Answer < Return to Assignment Units Provide Feedback ?
L21. Figure P4-21 shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is to be 500 lb, specify a suitable diameter for the steel pin if it is to be made from SAE 1040 WQT 900. 4-21
Use the drawing below to answer the following two questions. a. Determine the equivalent spring stiffness of the following system. Simplify the expression (ie – single common denominator. Your answer should be an expression of just K’s – no numbers). b. If the weight on top is 20 lb and the K1 = K4 = 50 lb/in, K2 = 33 lb/in and K3 = K5 = 25 lb/in, what is the natural frequency of the system?
1 300N forces on the pliers? 300N What forces are exerted on the bolt at E in the figure below as a result of the 30 mm 70 mm PIED PAR 30 mm D 30 mm 30 mm
Question 1: A race car is turning (cornering) on a flat road, as shown in Figure Q1-1. The speed of the car is 300 kph and the turning radius is 260 m. Having the car parameters as below, answer questions a) and b). ● . ● ● m = 890 (kg) (57% of the weight is on the rear axle); Air density = 1.225 (kg/m3); Equivalent aerodynamic lift coefficient for front axle= -0.915 (-); Aerodynamic frontal area= 1.11 (m²); Slip angle of the front tyres= +2.4 (°); Slip angle of rear tyres= +1.2 (°); The steering angle of wheels= -1.9 (°); The efficiency of the drivetrain from the engine to the contact patch of tyres is 100%. 8=-1.9°- ---R=260 m α = +2.4° αR = +1.2° Figure Q1-1 Motion of the vehicle and the angles a) Calculate the engine power delivered to tyres to overcome the total induced drag due to lateral force.
or the spring system given in Figure 1, create the clement matrices as well as the global stiffness and force matrix, note that k-1. -ww- Figure 1
topic: torsion in circular shafts The hollow shaft used in the system has the following conditions: Outer diameter (Ø): 150 mm Ø Allowable Shearing Stress: 85 MPa Determine the thickness (mm) of the shaft. Round to the nearest whole number for the thickness and use 2 decimal places for other solved values. Provide a torque diagram, strictly follow instructed sign convention, and start from left to right.
A series of three links is given with lengths of 2.4 ", 7.2" and 3.4 ", select the length of a fourth link, that when assembling the mechanism one of the links can be driven by a motor that rotates continuously. Mechanism is according to Grashoff, show all your operations to justify your results
Figure P1-71 shows a riveted butt joint with cover plates connecting two steel plates. Compute the 1-71. shear stress in the rivets due to a force of 10.2 kN applied to the plates.
Solve the problem. A 11-in. connecting rod in an engine connects the wrist pin of a piston at point A to the end of a second rod at point on the crankshaft. As the piston moves forward and back, the crankshaft is turned counterclockwise around point C. The stroke length of the engine is the distance that the piston travels (one way) with its cylinder. If the stroke length is 4 in., and the engine turns at 600 rpm, write a model representing the distance d (in inches) from A to the center of the crankshaft Cas a function of time t (in minutes). Assume that at t = 0, the piston is at its farthest point from the crankshaft. B B C C B A A stroke length
An element made of AISI 1020 CD steel is shown, but to shape it, it had to be machined. It must have a reliability of 99.9999%.It is subjected to the loads P₁= 200 pounds and P₂= 400 pounds; In others, the force in the "z" direction does not act, but the force in "y" remains with the same magnitude, but is completely reversed, in the positive and negative sense of the "y". Determine:to. The critical point of the system and for this establish the state of effort. Explainb. Apply Mohr's circle to the critical stress state and obtain σ1, σ2 and tmaxC Determine the safety factor and explain.
In the design in the figure, a force of Fn=45992 N acts in the vertical plane on a machine element with a diameter of D=200 mm on the shaft resting on the A and B bearings. If the angle made by this force with the horizontal is b=40o, find the life of the 6210 coded Deep Ball bearing to be used in the B bearing, in hours. Number of revolutions = 30 rpm. 1-) The diameter of the machine element on which the force acts will be taken into account in the calculation of bearing forces (That is, it will be assumed that the Fn force AFFECTS THE GROUND shown in the figure, NOT the axis of the shaft). 2-) Pi number will be taken as 3.14.