Question 5 a) Table Q5a shows the operation of a JK flip-flop : Inputs Outputs J K 1 1 1 1 1 1 Q Q Table Q5a : JK flip-flop Operation How is this an improvement on the operation of an S-R flip-flop and briefly describe how this improvement is achieved ? i) State the truth table for a T-type flip-flop and sketch how the JK flip-flop can be used to implement it. Complete table Q5b by identifying all possible input conditions that achieve the output transitions shown. ii) iii) Transition Inputs Qn Qn+1 J K 1 → 0 1 → 1 Table Q5b : JK flip-flop Output Transition Input Control

Question 5 a) Table Q5a shows the operation of a JK flip-flop : Inputs Outputs J K 1 1 1 1 1 1 Q Q Table Q5a : JK flip-flop Operation How is this an improvement on the operation of an S-R flip-flop and briefly describe how this improvement is achieved ? i) State the truth table for a T-type flip-flop and sketch how the JK flip-flop can be used to implement it. Complete table Q5b by identifying all possible input conditions that achieve the output transitions shown. ii) iii) Transition Inputs Qn Qn+1 J K 1 → 0 1 → 1 Table Q5b : JK flip-flop Output Transition Input Control

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

c) d) Explain the different between sequential circuit and combinational circuit. a) Identify input conditions necessary in order to set, reset and toggle the JK flip flops in Figure Q3d(i) and Q3d(ii). Clock QUESTION 4 J K Q व Figure Q3d(i) Clock S R Clock Convert the SR flip-flop in Figure Q4a to behave like JK flip-flop. ā Figure Q4a a J K Q ā Figure Q3d(ii)
Two edge-triggered J-K flip-flops are shown in figure below. If the inputs are as shown, draw the Q output of each flip-flop relative to the clock, and explain the difference between the two. The flip-flops are initially RESET. CLK CLK -C CLK- K K (b)
The state diagram is a basic 3-bit Gray code counter. This particular circuit has no inputs other than the clock and no outputs other than the outputs taken off each flip-flop in the counter. Show the state table, Karnaugh maps, and counter implementation using JK flip-flop.
Show the digital circuit diagram, output waveforms and truth table of a modulo-5 up counter using toggle flip-flops and explain the working principle.
Given the state diagram and D flip-flop, derive the state table, Flip-flop input equation and output equation, and logical diagram.
Write the next-state equations for the flip-flops and the output equation. (b) Construct the transition and output tables. (c) Construct the transition graph. (d) Give a one-sentence description of when the circuit produces an output of 1. Q2 D2 Q1 T1 CLK Figure 4
4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially Low. HIGH CLK- CLR nnnnnnn CLK PR CLR
please draw a logic diagram with following description Two D flip-flops (DFF1 and DFF0): DFF1 stores Q1 DFF0 stores Q0 Combinational logic for D flip-flop inputs (D1 and D0): D1 = Q1 & power D0 = power & (Q1 ^ sensor) Output signals (A, B, C , and D): A = ~(Q1 | Q0) B = ~Q1 & Q0 C = Q1 & ~Q0 D = Q1 & Q0
Complete the design process using full encoding and D-flip flop for the the function described by the follow state diagram and draw the schematics.
Draw the block diagram of a positive-edge triggered master-slave D flip-flop.
Use D flip-flops to design a mod-16 binary down counter, whose counting sequence is 1111->1110->1101->1100->1011-> … ->0000->1111…. Derive the logic expressions for the D inputs of the flip-flops and draw the circuit diagram.
4- Draw the output waveform if the signal shown in Figure below is applied to inputs of J-K Flip-Flop. Q is initially LOW. PR HIGH CLK- K CLR CLK- PR CLR