Question 2)) In this figure .A 50mm diameter agitator propeller shaft of is utilized to drive a rotor blade in a mixer. As a consequences, the shaft is suffered a compressive load of P =125KN and a torque of T=2.4KN.m. find the principle stresses and maximum shear stress. Check if it is safe to use basing on Tresca failure criterion. The yield stress of the shaft is 480MPA -T

Question 2)) In this figure .A 50mm diameter agitator propeller shaft of is utilized to drive a rotor blade in a mixer. As a consequences, the shaft is suffered a compressive load of P =125KN and a torque of T=2.4KN.m. find the principle stresses and maximum shear stress. Check if it is safe to use basing on Tresca failure criterion. The yield stress of the shaft is 480MPA -T

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
A pipe with an outside diameter of 4.0 in. and an inside diameter of 3.624 in, is subjected to an axial force of P-850 lb, a horizontal force of Pz 1560 lb, and a concentrated torque of T-2940 lb-in, acting in the directions shown. Assume a 49 in. Section propertles for the pipe are A-2.2514 in.?,J-8.199 in.", and ly 1-4.0995 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element Answer: Oy = psi Txy psi
a solid shaft is transmitting 1 mw at 240 rpm determine the daimeter of shaft exceed the mean of torque 20% take maximum shear alloy stress as 55mpa
A solid steel shaft has to transmit 75Kw power at 200 pm. Taking allowable shear stress 70Mpo. Find suitable dia of shaft with the maximum torque transmitted on each revolutions exceeds by mean by 30% 1.3 times mean.
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows : F, = 1590 N; F, = 580 N Pulley Gear F1 A D F, -100 : 200- 100→ All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa; Yield strength = 380 MPa; Factor of safety = 1.5.
A shaft made of steel receives 7.5 kW power at 1500 r.p.m. A pulley mounted on the shaft as shown in Fig. has ratio of belt tensions 4. The gear forces are as follows: F,= 1590 N; F, = 580 N Pulley T1 Gear F, A D F, -100- 200- 100 All dimensions in mm. Design the shaft diameter by maximum shear stress theory. The shaft material has the following properties : Ultimate tensile strength = 720 MPa: Yield strength = 380 MPa; Factor of safety = 1.5.
A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torqueif the shear stress is not to exceed120 MPa in N-m.
A pipe with an outside diameter of 55 in. and an inside diameter of 5.067 in. is subjected to an axial force of P,-660 lIb, a horizontal force of P,-1520 lb, and a concentrated torque of T-2770 lb-in, acting in the directions shown. Assume a- 29 in. Section properties for the pipe are A-35936 in2, J-25.1213 in.", and I,-1,-12.5606 in.. Determine the normal and shear stresses at point K, and show these stresses on a stress element K T. Answer: psi Ty" psi
A hollow shaft has an inner diameter of 0.035 m and an outerdiameter of 0.06 m. Compute for the torque if the shear stress isnot to exceed 120 MPa in Nm.
A winch raises a 60# bucket of paint, as shown. The main shaft of the winch is simply supported by bearings at A and C. The winch uses a 6"diameter pulley (B) and torque is applied at the end of the shaft to pull the cart. Determine the minimum shaft diameter based on the Distortion Energy (Von Mises) criterion using on a yield strength of 50ksi and a design factor of 2.0. 12" winch 18" C A Paint Rope
Flat belt 100mm wide and 8mm thick transmits power between two pulleys, running at 1600 m/min. The mass of belt is 0.9kg/m length, the angle of lap in the smaller pulley is 1650 and the coefficient of friction between the belt and pulleys is 0.3, If the maximum permissible stress in the belt is 2MN/m2, find the maximum power transmitted. 1 Add file
Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque of T N. m. the missing Torque 171 (T).