A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. It ispress fit on a solid shaft of same material with diameter 42mm such that the nominal diameter betweensleeve and shaft became 41mm.a. Find the pressure developed between shaft and sleeve.b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft.c. Find the maximum shaft diameter that can be used before failure.

Answered: Image /qna-images/answer/3a0fda5d-771f-4537-95a2-4b856cf13a48.jpg

A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter betwee sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.

A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press fit on a solid shaft of same material with diameter 42mm such that the nominal diameter betwee sleeve and shaft became 41mm. a. Find the pressure developed between shaft and sleeve. b. Draw the tangential, radial, and total stress as a function of radius, for both sleeve and shaft. c. Find the maximum shaft diameter that can be used before failure.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Compute the torsional shear stress in a circular shaft with diameter of 50mm that is subjected to a torque of 800Nm.
show formula and calculation as fast as , don't hold the question for longer time. 1) The 2.3-in.-diameter drive shaft AB on the helicopter in (Figure 1) is subjected to an axial tension of 10 000 lb and a torque of 345 lb⋅ft. Determine the principal stresses and the maximum in-plane shear stress that act at a point on the surface of the shaft.
A flanged bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outsude diameter and 90 mm in inside diameter. If the allowable aring stress in the shafts and the bolts is 60 MPa, how many 10 mm diameter steel bolts must be used on a 200 mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
A hollow steel shaft is to transmit 4,867 N-m of torque and is to be sized so that the torsional stress does not exceed 176 MPa. If the inside diameter is three-fourths of the outside diameter, what is the exact outside diameter size of the shaft in mm?
500 lb in. 1200 lb - in. 400 lb - in. dep-0.9 in. dec =0.75 in. B dan = 0.6 in. Specifications: Shafts AB, BC, CD are solid material. Determine: a) The shaft section in which the maximum shear stress occurs and the magnitude of the stress. Now consider that the shaft is tubular with a 0.300 inner diameter. Determine: b) The shaft section in which the maximum shear stress occurs and the magnitude of the stress.
1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, and the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel P E=2.1x10$ N/mm?, Tmax (1-Q¿)
A hollow shaft has an inner diameter of 0.035m and outer diameter of 0.06m. Compute for the torqueif the shear stress is not to exceed120 MPa in N-m.
Compute the torsional shear stress that would be produced in a solid circular shaft having a diameter of 20 mm whe subjected to a torque of 280 N m.
Bearing stress 4. Please provide proper discussion and illustration also complete solution and clear solution please thank you Determine the length of a square key to be used for a 3.73 kW, 1800 rpm electric motor if the motor shaft diameter is 35 mm and the width of the key is approximately one-fourth of the shaft diameter. The allowable shearing stress on the key is 2.45 MPa
an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of twist must not go over 3 1/2 degrees in the 6ft. pick the economical shaft size.
Calculate diameter of shaft using maximum shear stress theory,when equivalent torque of 800 x 103 N-mm acts on the shaft. 80 Mpa is the allowable shear stress for the shaft