Question 1: Saturated steam enters a converging-diverging nozzle at 1.75 MPa, 10 percent moisture, and negligible velocity, and it exits at 1.2 MPa. The nozzle exit area is 25 cm². You can assume the nozzle is isentropic, the flow through the nozzle is steady and one-dimensional, and the nozzle is adiabatic. Determine (a) the exit velocity, (b) the mass flow rate, (c) the Mach Number, (d) the throat area. Vi ≈ 0 Steam a) N = 100%

Question 1: Saturated steam enters a converging-diverging nozzle at 1.75 MPa, 10 percent moisture, and negligible velocity, and it exits at 1.2 MPa. The nozzle exit area is 25 cm². You can assume the nozzle is isentropic, the flow through the nozzle is steady and one-dimensional, and the nozzle is adiabatic. Determine (a) the exit velocity, (b) the mass flow rate, (c) the Mach Number, (d) the throat area. Vi ≈ 0 Steam a) N = 100%

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fuel with heating value (HV) of 39,000 kJ/kg is burned by spraying in to 16-cm-diameter tabular combustionchamber. The air enters at 450 K, 380 kPa, and 55 m/s as shown in Figure Q3. If the exit Mach number is 0.8,determine (a) the exit temperature and,(b) the rate at which the fuel is burned.Properties of air: Specific heat capacity ratio k = 1.4, Specific heat at constant pressure c, = 1.005 kJ/kg.K,and Gas constant R = 0.287 kJ/kg.K.Use Appendix 2 for Rayleigh flow functions for an ideal gas with k = 1.4 Assume:1. Rayleigh flow (i.e., steady one-dimensional flow of an ideal gas with constant properties through aconstant cross-sectional area duct with negligible frictional effects) are valid. 2. combustion is compleso, and it is treated as a heat addition process, with no change in the chemical composition of flow 3.The increase in mass flow rate due to fuel in ection is disregardeo.
Steam expands isentropically in a converging/diverging nozzle from inlet conditionsof 1400 kPa, 325°C, and negligible velocity to a discharge pressure of 140 kPa. At thethroat, the cross-sectional area is 6 cm2. Determine the mass flow rate of the steamand the state of the steam at the exit of the nozzle.
Air flows steadily through a varying cross-sectional area duct such as a nozzle at a mass flow rate of 10 lb/s. The air enters the duct at a pressure of 200 lb/in2 and 445°F with a low velocity, and it expands in the nozzle to an exit pressure of 30 lb/in2. The duct is designed so that the flow can be approximated as isentropic. Determine the density, velocity, flow area, and Mach number at each location along the duct that corresponds to an overall pressure drop of 30 lb/in2.
A gas initially at a supersonic velocity enters an adiabatic diverging duct. Discuss how this affects (a) the velocity, (b) the temperature, (c) the pressure, and (d ) the density of the fluid.
Argon gas is approaching a converging–diverging nozzle with a low velocity at 20°C and 150 kPa, and it leaves the nozzle at a supersonic velocity. If the cross-sectional area of the throat is 0.015 m2, the mass flow rate of argon through the nozzle is (a) 0.47 kg/s (b) 1.7 kg/s (c) 2.6 kg/s (d ) 6.6 kg/s (e) 10.2 kg/s
Air is approaching a converging–diverging nozzle with a low velocity at 20°C and 300 kPa, and it leaves the nozzle at a supersonic velocity. The velocity of air at the throat of the nozzle is
Air at 14 psia, 40°F, and a Mach number of 2.0 is forced to turn upward by a ramp that makes an 8° angle off the flow direction. As a result, a weak oblique shock forms. Determine the wave angle, Mach number, pressure, and temperature after the shock.
Products of combustion enter a gas turbine with a stagnation pressure of 0.90 MPa and a stagnation temperature of 840°C, and they expand to a stagnation pressure of 100 kPa. Taking k = 1.33 and R = 0.287 kJ/kg·K for the products of combustion, and assuming the expansion process to be isentropic, determine the power output of the turbine per unit mass flow.
A gas initially at a subsonic velocity enters an adiabatic diverging duct. Discuss how this affects (a) the velocity, (b) the temperature, (c) the pressure, and (d ) the density of the fluid.
A fan is used to transport CO2 gas (MW = 44 g/mol) gas at rest @ 700mmHg. At the discharge end, the pressure is 765mmHg, and the velocity is 100 m/s. Assuming the flue gas behaves ideally, and the process is isothermal, with the temperature maintained at 100C. Determine the theo. power required to move 45000 m /h of the flue gas.
Nitrogen enters a converging–diverging nozzle at 800 kPa and 400 K with a negligible velocity. Determine the critical velocity, pressure, temperature, and density in the nozzle. Use data from the tables. The properties of nitrogen are k = 1.4 and R = 0.2968 kJ/kg·K
Hydrogen entering a supersonic nozzle at 450 m/s. The inlet conditions are 10 kPa and 450 °C. The nozzle exit diameter is adjusted such that the exiting velocity is 800 m/s. The exiting temperature is nearest: