E=240 GPa and I = 65.0(106) mm*(Figure 1)Figure10 kN3 kN/m-3 m1 of 1Part ADetermine the slope of end A of the cantilevered beamExpress your answer to three significant figures and include the appropriate units.μÀja XbXaX.10A=1.44110-510 5 radSubmit Previous Answers Request AnswerReturn to AssignmentX Incorrect; Try Again; 3 attempts remainingXProvide Feedback?TODO

Answered: Image /qna-images/answer/e0cf887d-6818-4de8-85d1-26e1dcd26284.jpg

E=240 GPa and I = 65.0(105) mm (Figure 1) Figure 10 kN 3 kN/m 1 of 1 Part A Determine the slope of end A of the cantilevered beam Express your answer to three significant figures and include the appropriate units. μA . X-10 ₁=1.44110-5 rad Submit Previous Answers Request Answer < Return to Assignment X Incorrect; Try Again; 3 attempts remaining X Provide Feedback ?

E=240 GPa and I = 65.0(105) mm (Figure 1) Figure 10 kN 3 kN/m 1 of 1 Part A Determine the slope of end A of the cantilevered beam Express your answer to three significant figures and include the appropriate units. μA . X-10 ₁=1.44110-5 rad Submit Previous Answers Request Answer < Return to Assignment X Incorrect; Try Again; 3 attempts remaining X Provide Feedback ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P=1623N, T=4552Nm, a=0.77m, b=1.13m, c=0.78m, w=39mm, and h=80mm. Round off the final answer to five decimal places. Show your complete solution.
asap
H = In the figure, he, hr, z and the measured slope length I were 5.74 ft, 5.50 ft, 96° 18'56", and 403.21 ft, respectively. Calculate the horizontal length between A and B if a total station measures the distance. Express your answer to six significant figures and include the appropriate units. μÃ Value Units Datum ? eleva
A (160+Reg. No.) kN force is applied as shown at the end of a hot-rolled steel beam. Neglecting the effect of fillets and of stress concentrations, perform calculations in MS excel or MATLAB for the principal stresses in the beam to satisfy a design specification that they be equal to or less than 150 MPa. If the principal stresses are more than the given value, what would you change in the beam so that satisfy the required stresses. 210 mm 13 mm a 1035 mm 110 mm 160kN +Reg No. 0.4m (b) (a) Figure: Hot-rolled cantilever steel beam a) 3D view of the beam b) Cross-section of the beam
Figure Part C Ive = toft > Value Use Mohr's circle to determine the moment of inertia of the beam's cross-sectional area about the u axis. Set a 45 in 6-2 in (Ege1) Express your answer with the appropriate units. 1.- Value Submit Part B 1.- Value Submit Use Mohr's circle to determine the moment of inertia of the beam's cross-sectional area about the axis Express your answer with the appropriate units. Part C Request Answer Units Units A Use Mohr's circle to determine the product of inertia of the beam's cross-sectional area with respect to the u and u axes. Express your answer with the appropriate units. 2 Units ?
Part A The state of stress at a point in a member is shown on the element. Suppose that oe = -50 MPa, oy = -100 MPa. , Tzy = -29 MPa. Determine the normal stress component acting on the plane AB. (Figure 1) Express your answer with the appropriate units. HÁ ? Figure 3 1 of 1 87.614 MPa Oe = A Submit Previous Answers Request Answer X Incorrect; Try Again; 5 attempts remaining 30 Part B Determine the shear stress component acting on the plane AB. В Express your answer with the appropriate units.
Question 1. W₂ y: ← WI Calculate y, the distance from the base to the position of the Neutral Axis of the T-section shown above (not drawn to scale). The bottom section has width w₁ = 10mm and height h₁ = 60mm. The top section has width w₂ = 50mm and height h₂ = 14mm. Enter your answer in millimetres correct to two decimal places. mm hi Type here to search 122 4313 O Af
A 1D two-node bar element as shown below is considered. The displacement of node 1 is q₁=0.002 mm, and the displacement of point pis qp=0.013 mm. Using 1D linear shape functions, determine the displacement of node 2 (92) in mm? Hint: round off your final answer to 5 decimal places; e.g. if your answer is 1.2345678, then rounding-off to 5 decimal places yields 1.23457 and that is the value which you need to type in the answer box. 1 P
W 8 L/2 1/2 Wz
strength of material MENG222 Please solve the problem step by step and make your line clear and don't forget FBD and show me your step Please make sure your answer is correct please p1=123 p2=12
The bar is supported by a roller constraint at B, which allows vertical displacement but resists axial load and moment. The bar is subjected to the loading shown in (Figure 1). Suppose that P300 lb. EI is constant. Follow the sign convention. Figure 8 ft C -8 ft Part A Determine the slope at A. Express your answer using three significant figures. 0A- 1380 Submit τVE ΑΣΦΙΞ vec • Part B Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining Determine the deflection at C. Express your answer using three significant figures. ΠΛΣΦΙΞ vec ^ vc= 0.0161 VC= Submit Previous Answers Request Answer * Incorrect; Try Again; 5 attempts remaining P ? ? x 1 k-ft² EI X 1 k-ft³ EI x
n the tru /take/questions/28377487 In the truss shown, find the value of L1 in degrees. 56 38' 58*20' 41 42'