For the circuit shown, give the sequence of operation of cylinders 1 and 2 when the pump is turned on. Assume both cylinders are initially fully retracted. CYLINDER 1 CYLINDER 2 $49 Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle repeats. Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle stops. Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle repeats. O Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle stops..

For the circuit shown, give the sequence of operation of cylinders 1 and 2 when the pump is turned on. Assume both cylinders are initially fully retracted. CYLINDER 1 CYLINDER 2 $49 Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle repeats. Cylinder 1 extends, cylinder 2 extends. Cylinder 1 retracts, cylinder 2 retracts. Cycle stops. Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle repeats. O Cylinder 2 extends, cylinder 1 extends. Cylinder 2 retracts, cylinder 1 retracts. Cycle stops..

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter8: Computer Numerical Control

Section8.3: Cnc Turning: Programming

Problem 11RQ: List two types of canned cycles besides roughing turning and finish turning.

See similar textbooks

Similar questions

QUESTION 13 Match the following operation for the SI engine with respect to the revolution of the part concerned. v Point 1 of a 4-stroke A. Exhaust Port Open v Point 2 of a 4-stroke B. Spark Ignition v Point 3 of a 4-stroke C. Inlet Valve Opens, 10 D. Exhaust Valve Closes v Point 4 of a 4-stroke E. Exhaust Valve Opens v Point 5 of a 4-stroke F. Induction Port Open v Point 1 of a 2-stroke G. Inlet Valve Closes v Point 2 of a 2-stroke H. Transfer Port Open v Point 3 of a 2-stroke QUESTION 14 Click Save and Submit to save and submit. Click Save All Answers to save all answers. Type here to search
1. Two double acting pneumatic cylinders (A, B) in a process industry should extend together at the same time to open two different valves. On the return stroke both cylinder rods return at the same time. The starting is by a detent switch. Both the cylinders are of the same size with the same stroke length. In terms of notation, the cycle is required to go on till the detent start-up switch is pressed again. Draw the electro pneumatic circuit neatly. Briefly explain its operation. LB +J LB A В Y Y Y Y V
Match the following operation for the SI engine with respect to the revolution of the part concerned. Point 1 of a 4-stroke A. Exhaust Valve Opens Point 2 of a 4-stroke B. Exhaust Valve Closes c. Induction Port Open Point 3 of a 4-stroke D. Inlet Valve Opens, 10 Point 4 of a 4-stroke E. Spark Ignition F. Transfer Port Open G. Exhaust Port Open Point 5 of a 4-stroke Point 1 of a 2-stroke Point 2 of a 2-stroke H. Inlet Valve Closes Point 3 of a 2-stroke
Question Two: The crank shaft of an engine runs at 2400 rpm. If it takes 0.002 second after ignition for the charge to gain maximum pressure, what should the crank angle be when spark occurs. If the inlet valve opens 12° before T.D.C. and closes 43° after B.D.C. for how long is it open during one cycle?
In 40 seconds, the crankshaft of a truck engine operating at _______rpm turn thru 8000 radians.
Answer the following question: What is Ground movement of an aircraft engine starting and operation?
Define Cycle slips and how they are created?
Draw cycle and system diagram i well give thumb up
Question: What controls the instroke of a Single-Acting Cylinder? Note: -NO PLAGIARISM PLEASE. -200 words or more.
Reciprocating engine is an inversion of four bar kinematic chain. Select one: True False
The piston rod of a double-acting cylinder is to advance when a 3/2- way push button valve is actuated manually. The cylinder is to remain advanced until a second valve is actuated. The signal of the second valve can only take effect after the first valve has been released. The cylinder is to then return to the initial position. The cylinder is to remain in the initial position until a new start signal is given. The speed of the cylinder is to be adjustable in both directions.Draw the circuit diagram for the problem.
Industry Print Exercise 23-2 Refer to print PR 23-2. The sequence of operations for this print is given below. Answer the questions following the sequence of operations. Sequence of Operations descends at a controlled rate, slowly compacting the explosive charge to avoid detonation due to a sudden Description: This is a system to control a 90-ton hydraulic, explosive-compaction press. The press ram shock. 1. The cycle is started by energizing solenoid A, which shifts control valve 3 and supplies pressure to the head end of the hydraulic cylinder (7). This operates the ram. 2. The cylinder (7) extends at a slow rate controlled by the fluid in the rod end of the cylinder, which is vented through the flow control valve (5). the 1. When de-energizes solenoid A and energizes solenoid B. This shifts control valve 3 to retract the cylinder (7). de rol valve 5 has an integral check valve that permits the free flow of fluid in the opposite direction, causing the cylinder (7) to rapidly retra…