Ques. 1 Water is flowing through a pipe having diameters 600 mm and 400 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 350 kN/m and the pressure at the upper end is 100 kN/m. Determine the difference in datum head if the rate of flow through the pipe is 60 litres/sec. D, 400 mm 100 kN/m P2 D, 600 mm ---- P 350 kN/m Datums line

Ques. 1 Water is flowing through a pipe having diameters 600 mm and 400 mm at the bottom and upper end respectively. The intensity of pressure at the bottom end is 350 kN/m and the pressure at the upper end is 100 kN/m. Determine the difference in datum head if the rate of flow through the pipe is 60 litres/sec. D, 400 mm 100 kN/m P2 D, 600 mm ---- P 350 kN/m Datums line

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4.80 Water (p = 62.4 lbm/ft³) flows from the large orifice at the bottom of the tank as shown. Assume that the flow is irrotational. Point B is at zero elevation, and point A is at 1 ft elevation. If VA = 4 ft/s at an angle of 45° with the horizontal and if VB = 12 ft/s vertically downward, what is the value of PA - PB? Answer B Vertical Problem 4.80 45°
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
3. A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 700 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 100 mm dia. 45.0 m 540 m
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
4. Evaluate the pressure at the center of pipe A. Given: y of Liquid 1 = 12 kN/m y of Liquid 2 = 25 kN/m. hi = 60 cm h2 = 10 cm L = 60 cm а. -750 Рa c.-650 Pa b. -800 Pa d. -700 Pa Liquid 1 Liquid 2 h, h2
A pipe carrying oil (SG = 0.877) change in size from 150mm diameter in point 1 to 450mm diameter in point 2. Point 1 is 3.6m lower than point 2 and the pressure at point 1 is 90KPA while on point 2, the pressure is 60KP.. If the discharge is 150 L/s, determine the head lost and the direction of flow (A Direction cannot be determined B Direction is point 1 to point 2 C) HL = 4.38 m D HL = 7.11 m E HL = 5.13 m (F) HL = 3.51 m G Direction is point 2 to point 1
What is pipe roughness? A pump is located 5 m above the surface = 8170 M/m¹) in a closed tank. The pressure in the space above liquid surface is 35 Kpa. The suction line to the pump is 15 m of 15 cm diameter pipe (/= 0.025). The discharge from the pump is 60 m of 20 cm diameter pipe (/= 0.03). The pipe discharges in a submerged fashion to an open tank whose free liquid surface is 3 m lower than the liquid surface in the pressure tank. If pump puts 1.5 kW Into the liquid, determine the flow rate and the pressure in the pipe on the suction side of the pump. Assume turbulent flow.
Two pipes connected in parallel having a total discharge of 0.05 cu. m/s If pipe A has a total head loss of 0.5 m whose length and diameter are 200 m and 150 mm respectively. Pipe B have a length of 100m and diameter of 200mm. If they have the same friction factor f = 0.02. Compute the discharge at pipe Ba. 0.04 cum/s b. 0.01 cum/sc. 0.02 cum/sd. 0.03 cum/s
Water flow at a 250mm diameter horizontal pipe 90m long. The friction factor is 0.023. If the pressure at the starting point is 80KPA and the pressure at the end point is 50KPA. Determine the discharge at the pipe. A Q = 118.43 L/s В Q = 132.74 L/s Q = 101.07 L/s D Q = 172.81 L/s Q = 153.68 L/s No answer among the choices
Given a three-pipe system, the total pressure drop is P,- P, 150,000 Pa, and the elevation drop is Z, - Z, = 5 m. The pipe A data are: Pipe L, m d, cm E, mm eld 1 100 8 0.24 0.003 2 150 0.12 0.002 3 80 4 0.20 0.005 The fluid is water (density 1000 kg/m' and kinematic viscosity 1.02x10 m/s). Calculate the flow rate Q in m'/h through the system. 3
A circular orifice of 50 mmdiameter is fixed to the end of a water pipe of 75mm diameter. The gauge pressure in the pipe is70 kPa. The flow out of theorifice was measured as0.017 m^3/second. Theactual jet velocity wasmeasured by pitot tubewith a value of 12 m/s.a. Determine Cv, Cc and Cd.b. Calculate the head loss.
Given a three-pipe system, the total pressure drop is PA - PB = 150,000 Pa, and the elevation drop is ZA ZB = 5 m. The pipe data are: Pipe 1 2 3 L, m 100 150 80 A. O 0.00283 m³/s O 0.00146 m³/s The fluid is water (density 1000 kg/m³ and kinematic viscosity 1.02x10-6 m²/s). Calculate the flow rate Q in m³/h through the system. (3 O 0.00675 m³/s O 0.00834 m³/s d, cm 8 6 4 1 €, mm 0.24 0.12 0.20 2 eld 0.003 0.002 0.005 • B