ISTINYE ISU UNIVERSITY Question 2: A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², E. -1.9×10¹¹ N/m².

ISTINYE ISU UNIVERSITY Question 2: A steel pipe is used to drain water from a reservoir that is 50 m above the datum, and water is discharged into the air at the elevation of the datum. The pipe is 1500 m long and 450 mm diameter and 50 mm wall thickness. A valve is installed at the downstream end of the pipe allows a flow rate of 0.71 m³/s. The valve was completely closed in 1.4 sec. Calculate maximum hammer pressure at the valve. The pipe is longitudinally anchored. Eb = 2.1×10° N/m², E. -1.9×10¹¹ N/m².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. A pump is used to transport water at the rate of 0.075 m³/s from a reservoir 20 m above the pump to a free discharge 35 m above the pump. The pressure on the intake side of the pump is 150 kPa and the pressure on the discharge side is 450 kPa. All pipes are commercial steel of 15 cm inner diameter. Determine (a) The head supplied by the pump (b) The total head loss between the pump discharge and point of free discharge. Z₁=20 m 1 P₂ = 150 kPa 2 面 3 D=15 cm A P3=450 kPa 4 Free Discharge Z4 = 35 m
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
Question 4 Water flows upwards in a vertical (plane) pipe line of gradually varying cross section from point 1 to point 2, which is 1.5 m above point 1, at the rate of 0.9 m³/s. At section 1 the pipe dia is 0.5 m and pressure is 800 kpa. If pressure at section 2 is 600 kpa determine the pipe diameter at that location. (neglect the losses) tt thele loloses)
A pipeline 200 meters long delivers water from an impounding reservoir to a service reservoir with the difference in water levels of 20 meters. The pipeline of commercial steel is 400 mm in diameter. It has two 90 degree flanged elbows, a check valve, and an orifice (K_m= 2.5). Determine the flow through the pipe. Use a water temperature of 20 degrees Celcius.
A rigid pipe has a diameter of 150 mm and a length of 1020 m. The water flowing in the pipe has a bulk modulus of 2.0164 x 10 N/m². Determine the maximum permissible discharge (in L/s) if the water hammer pressure is not to exceed 1400 kPa when the outlet valve is suddenly closed. If the valve closure takes 4 seconds, determine the increase in pressure.
Water flows through a set of pipes from a reservoir to the point of use, 12.5 m below thewater surface of the reservoir. The first pipe has a diameter and length of 125 mm and 20 mrespectively. The second pipe has a diameter of 175 mm. Determine the length of the secondpipe if a flow rate of 0.065 m3/s is required at the outlet of the second pipe. The first pipehas a friction coefficient of 0.008 (Darcy) and the second pipe has a friction coefficient of0.005 (Darcy). Consider all losses.
1. Water flows through Pipe A and into parallel pipes 1,2 and 3, and out through Pipe B. The properties of the pipes are listed as follows: Pipe Length (m) Diameter (cm) 30 Friction Coefficient, f A 1 300 10 0.020 240 600 2 15 0.018 3 20 0.017 В 30 The upstream junction (near A) has an elevation of 90m with a pressure of 205 KPa; the downstream junction is at elevation 30 m. If the average velocity in Pipe A is 3.0 m/s, find the pressure at the downstream junctions and rate of flow in each pipe. Also, draw the pipe system.
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
the end of tank containing is vertical and has the shape of the bottom of a half circle radius 10m. determine the hydrowtate against the end of the tank
2. A 20mm diameter commercial steel pipe, 30m long is used to drain an oil tank. Determine the discharge when the oil level in the tank is 3m above the exit of the pipe. Neglect minor losses and assume f = 0.12. D=20mm, L=30 m, f-0.12 3 m
QI/ Water flows from the reservoir on the left to the reservoir on the right at a rate of 0.45 ms. The formula for - Ekevation? the head losses in the pipes is h - 0.02 L: D 2g What elevation in the left reservoir is required to produce this flow? Also carefully sketch the HGL and the EGL for the system. Note: Assume the head-loss formula can be used for the smaller pipe as wel as for the Elevation 34 m 80 m 90 m D, =0.344 m A, -0.1 m D,= 0.486 m A- 02 m larger pipe. Q2/ A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L= 2000 m? The head loss in the pipe is 0.02(L/D)V + Eerhm- 0n -D02m 28 Detn where Lis the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and Elvation =m L-2000m (2. Dis the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 mls, Q3/ For the parallel-pipe system of L-250 D-3 in Fig. each pipe is cast iron, and the pressure drop p -…