A pump draws water from reservoir A and lifts it to reservoir B as shown. The loss of head from A to 1 is 3 times the velocity head in the 150mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100mm pipe. When the discharge is 20 liters/sec. Compute the pressure head at point 1 and 2. B EL240M ELO 150 mm EL-20m 100 man

A pump draws water from reservoir A and lifts it to reservoir B as shown. The loss of head from A to 1 is 3 times the velocity head in the 150mm pipe and the loss of head from 2 to B is 20 times the velocity head in the 100mm pipe. When the discharge is 20 liters/sec. Compute the pressure head at point 1 and 2. B EL240M ELO 150 mm EL-20m 100 man

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Situation # 4: The pump shown draws water from the reservoir A at elevation 10m and lifts it to reservoir B at elevation 60m. The loss of head from A to 1 is two times the velocity head in the 200mm diameter pipe and the loss of head from 2 to B is ten times the velocity head in the 150mm diameter pipe. Determine the relate horsepower of the pump and the pressure heads at 1 and 2 in meters when the discharge is 0.03m/sec. El. G0 m El. 30 m 500 m 200 rm El. O m FUMP
A pump draws water from a reservoir A and lifts it to reservoir B as shown. The loss of head from A and lifts it to reservoir B as shown. The loss of head from A to (1) is 5 times the velocity head in the 12-inch pipe and the loss of head from (2) to B is 23 times the velocity head in the 7-inch pipe. Compute the pressure heads (2) in ft when the discharge is 447 gpm. Round your answer to 2 decimal places.
A pump draws water at 20 liters per second from reservoir A and lifts it to reservoir B, as shown in Figure FM-P-113. The head loss from A to 1 is three times the velocity head in the 150-mm diameter pipe, and the head loss from 2 to B is fifteen times the velocity head in the 100-mm diameter pipe. Choices are in the images Determine: Power delivered by the pump in kW Pressure head at point 1 in m. Pressure head at point 2 inm.
A pump draws water from reservoir A and lifts it to reservoir B as showm, The head los from reservoir A to pipe 1 is 3 times its velocity head and the head loss for pipe 2 to reservoir B is 20 times the velocity head. When the discharge is 20 L/s a) Compute the horsepower output of the pump in kW b) Compute the pressure head at pipe 1 c) Compute the pressure head at pipe 2 EL Om pipe 1 150 mm pipe 2 100 mm -EL-20 m EL 240 m
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
3. A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is 700 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assuming f = 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 100 mm dia. 45.0 m 540 m
Calculate the mechanical power [hp] required on the pump shaft considering the hydraulic system Shown. The pipe is made of commercial steel (roughness = 0.0002 ft) and has two different diameters, up to the pump inlet the pipe is 2 inches with a length of 100ft and from the pump outlet the pipe is 4 inches with 400ft. All elements are screwed The flow rate circulating through the system is 0.5 ft3/s and the efficiency of the pump is 85%. The density of water is 1.94 slug/ft3 and has a viscosity kinematics 1.1x10-5 ft2/s
1) Determine the flow in Ips on the orifice between the 2 tanks shown below AIR 25kPa AIR 10kPa OIL S=0.80 OIL S=0.80 WATER WATER ORIFICE C0 60 D-50mmo 2,8m 2m 1.5m WL
The figure shows a siphon discharging oil (s=0.90). The siphon is composed of 8 cm pipe from A to B followed by 10 cm pipe from B to C. The head losses are: Point 1-2: 0.30 J/N Point 2-3: 0.20 J/N Point 3-4: 1.00 J/N Compute the discharge. Determine the pressure at points 2 and 3. 8 cm ø HEL. 5 m HEL. 3 m H10 em g EL. O DATUM
Water is flowing in the straight 100mm diameter coated cast iron as shown in the figure. Due to continous supply, the water level of the reservoir remains constant at all time. By using Darcy Weisbach and Hazen William's formula of head loss, determine the flow rate in the pipe. (Ans.: DW:1786.2 liters/min, HW: 2144.4 liter/min) EL85M 180 m opened end EL50M
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E