Qı/ Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at flow rate of Q = 0.1414 (m³/s). If Pi is 70 (Bar), P2 is 9.81 (Bar), f=0.02 and length of pipe from point No. (1) to point No.(2) is 15.67 (km). (1) Find the diameter of the pipe

Qı/ Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at flow rate of Q = 0.1414 (m³/s). If Pi is 70 (Bar), P2 is 9.81 (Bar), f=0.02 and length of pipe from point No. (1) to point No.(2) is 15.67 (km). (1) Find the diameter of the pipe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A fluid enters a 3" diameter pipe; the Reynolds number for the flow is 45,803. At what distance…

Q: . Water is flowing through a pipe, driven by only gravity (no pumping). a. If water is flowing…

Q: Question? H.W : Find the Reynolds number and estimate the type of flow, when used the water with…

Q: In the below system, the pump uses 20°C water. If z2 = 225 ft, what is the flow rate (in ft3/s) if d…

Q: 35. Water enters a heated tube of 2 mm diameter at 30C and leaves the tube at 60 C. Find the water…

A: Given Data The diamter of tube is:D=2 mm=0.002m The reynolds number is:Re=1000 The inlet…

Q: Diesel fuel with a specific gravity of 0.8, flows through the Venturi meter shown in figure below.…

Q: Determine the discharge at pipeline 3 in lit/sec assuming f=0.02 for all pipes.

A: Given data Discharge (Q)=0.86m^3/s Friction factor (f) =0.02

Q: A pipe, inside diameter 1.27 cm, water flows through the pipe at a rate of 0.5 liters per second at…

Q: Q₂/Suppose in Figure 2, the lengths and diameters of pipe 1 is 300 m x 0.3 m, Pipe 2 is 150 m x 0.2…

A: Given:Pipe 1: L1=300 m, d1=0.3 mPipe 2: L2=150 m, d2=0.2 mPipe 3: L3=250 m, d3=0.25 mWater…

Q: Determination of pipe diameter. What size of circular pipe is needed to produce a flow rate of 250…

Q: Find the pressure drop between locations a and b for flow in a pipe using the following data:…

Q: (Pipe Radius = 25mm) (5 =Local head loss coefficient) 1. Calculate the & values for Valve and Elbow.…

A: In pipe or tube system components, minor or dynamic pressure loss can be stated as ∆P…

Q: Water at 20°C is to be pumped from Reservoir 1 to Reservoir 2 at a rate of 3 m³/min through a 2000 m…

Q: Q1) Benzene with specific gravity of 0.8 flows through 200 mm diameter pipe at velocity of 5 m/s.…

Q: Water at 20°C flows through a 9 cm diameter pig as in Fig. The total length of pipe between flange…

A: Diameter = 9 cm Length = 75 cm Mass flow rate = 32.67 kg/s P1 = 73 kpa P2 = 41 kpa

Q: Consider the pipe-network given below. For whole pipes William-Hazen friction. factor of C= 100. All…

A: From conservation of mass (continuity equation), total volume flow rate entering pipe network must…

Q: nction if pipe Veločity 2 discharge and pipe diameter 60 mm. Find the discharge in I/hr and velocity…

A: Concept Of Fluid Mechanics Used

Q: The three tanks shown in the figure below are connected by new cast iron pipes (ɛ = 0.26 mm). The…

A: Given: To Determine: Flow rate in pipe 2 and 3 and required pump power.

Q: Keeping in mind continuity of flow, compute the velocity of flow for section C (Vc), the 6 inch…

A: Given Data

Q: 3- What is the volumetric flow rate at point 3 in the following pipe system? a) 3 b) 0.3 0.5 다미 e)…

Q: 32. Water at 100 F is pumped at a rate of 125 gpm to a reservoir 50 ft higher. The pipe length is…

A: Water temperature, T=100 FWater flow rate, Q=125 gpm=125448.83 ft3/s=0.2785 ft3/s 1…

Q: CHOOSE THE CORRECT ANSWER! Three pipes of 400 mm, 350 mm and 300 mm diameter are connected in…

A: To find: The flow in pipe 3. Given: The diameter of the pipes are d1=400 mm1 m1000 mm=0.4 m, d2=350…

Q: 49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and…

A: Given:To find:(a) Total pressure drop.(b) Diameter of the equivalent pipe.

Q: A pumped fluid distribution system is being designed to deliver 400 gal/min of water to a cooling…

A: Given: The flow rate, Q = 400 gal/min The pipe type = schedule 40

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: When any fluid having velocity V passes through a pipe of area A, then discharge through the pipe is…

Q: 1. A schedule-40 pipe necks down from 24 in at point A to 12 in at point B. 8 ft³/sec of 60°F water…

A: The diameter at point A is .The diameter at point B is .The flow rate of water is .The pressure head…

Q: 3) Given: Q = 14 lit/sec; For the suction pipe: diam. = 180mm with head loss = three times its %3D…

A: Given that, Volume flow rate, Q=14 lit/sec,Diameter of suction pipe, Ds=180 mm,Head loss of suction…

Q: The branched pipe as shown in figure below discharges water. The diameters of the pipe 1 is 1.5 cm,…

A: Given, Diameter of pipes , d1 = 1.5 cm , d2 = 4cm and d3 = 3.5cm Discharges in the pipes , Q1 = 21…

Q: 152.4 mm, Schedule 40 pipe line 91.4 m long conveys 3028 l/min of cold water from a pump to a point…

A: The frictional head loss in a pipe due to fluid flow can be calculated using the formula given below…

Q: EL..20m K=0.5 A= fi= 0.02 D₁-0.3m Lis 150m F₂2 0.02 Da= 0.6m L₂=240m Valve For Valve K= 0.2 EL.: 5m…

Q: a. Certain fluid is flowing in a circular pipe w/ Reynolds no. of 400. What will happen to the…

Q: A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm,…

Q: 2) Compute the corrected flow in the pipe network shown.Use n = 0.012.

A: Given Data:to find:Corrected flow in the pipe network.

Q: Q4: Three pipes (A, B and C), if diameter of A equal to B, diameter of A less than C by 25%,…

Q: Need detailed solution. 4 decimal places. Oil with a specific gravity of 0.82 is flowing in a pipe…

A: To find: The pressure at point 2. Given: The specific gravity of oil is SGoil=0.82. The inlet…

Q: C2. A circular pipe 1 of 535 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters…

Question

Q1/ Water flows in the pipe shown in Fig. No. (1) from point No. (1) to point No.(2) at
flow rate of Q = 0.1414 (m³/s). If P¡ is 70 (Bar), P2 is 9.81 (Bar), f=0.02 and length of
pipe from point No. (1) to point No.(2) is 15.67 (km).
(1) Find the diameter of the pipe
(2) Find flow velocity in the pipe.
(3) Draw the H.G.L. of flow in the pipe.
P2 =9.81 (Bar)
p1 = 70 (Bar)
400 m
Reference Line
30°
Fig.(1)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Oil (s.g. = 0.84) flows through a 29-in-diameter pipeline at 7214 gpm. Compute the average velocity in fps (ft/s). Round your answer to 2 decimal places.
7. A cylindrical pipe with water flowing downward at 0.02m ^ a / s has a top diameter of 0.08 m and boom diameter 0.04 m and the height of 1.5 m. Find the pressure difference between the pipes.
After analyzing the flow type in a refinery oil (s = 0.8, v= 1.94x10-4 ft2/s) flowing through a 9inch diameter pipe at (41/1000) ft3/s. Find the following a)centerline velocity b)the velocity at r = 2inch c)the frictional factor d)the shear stress at the pipe wall and e)the head loss per foot of pipe length.
Ex5:- From Figure shown, the pipe line have Qa = 15L/s, QB = 3QD, DA=100 mm, DB= Dc = 25mm, Dp= 50 mm and vc = 4m/s. Find the value of discharge and velocities for pipes A, B, C and D? %3D
Please show complete diagrams and solutions T.Y :) Use Bernoulli's Energy Equation Dislike if not followed A 24 in. pipe conducts water from reservoir A to a pressure turbine (elev. = 15'), which discharges through another 24 in. pipe into tailrace B (elev. = 0'). The loss of head from A to 1 is 5 times the velocity head in the pipe and the loss of head from 2 to B is 0.2 times the velocity head in the pipe. What must water surface elevation at the reservoir be maintained such that the energy given up in the turbine is 552 hp? Assume discharge equals 25 cfs. Express all dimensions in English units.
THE PROBLEM IS FROM THE BOOK: ENGINEERING THERMOFLUIDS, M. MASSOUD.
None
Q5