X Start your trial now! First week only $4.99! >QuestionWater at 20°C flows through a 9 cm diameter pipe which has a 180 cal bend,as in Fig. The total length of pipe between flanges 1 and 2 is 75 cm. n themass flow rate is 32.67 kg /s, Gauge pressure at p1 73 kPa, and p2-41 kPa.Neglecting pipe weight, determine the X component ( Shown on figure) of theforce to the nearest N which the flanges must withstand for this flow.

Diameter = 9 cm Length = 75 cm Mass flow rate = 32.67 kg/s P1 = 73 kpa P2 = 41 kpa

Water at 20°C flows through a 9 cm diameter pig as in Fig. The total length of pipe between flange mass flow rate is 32.67 kg /s, Gauge pressure at p Neglecting pipe weight, determine the X compom force to the nearest N which the flanges must wii

Water at 20°C flows through a 9 cm diameter pig as in Fig. The total length of pipe between flange mass flow rate is 32.67 kg /s, Gauge pressure at p Neglecting pipe weight, determine the X compom force to the nearest N which the flanges must wii

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q- fluids, The Coefficient of discharge of a orifice meter is 0.97. The time taken by fluid to cover…

Q: It has been found that the dimensionless pressure drop in a pipe depends on the Reynolds number and…

A: Given:Pipe Details:Kerosene Pipe: Length L=40m, Diameter D=10cm = 0.1 mWater Pipe: Diameter D=2cm =…

Q: For the horizontal laminar internal flow through a pipe of diameter (d), if the veloci -1 dP (r)%3D…

Q: Fresh water at 20°C flows from reservoir A to reservoir B as indicated. Calculate the flow rate by…

Q: 3. Oil is flowing with 0.001m /s in a conduit with cross section as shown in the Figure where the…

A: Given data oil flow rate:-0.01 m3/secdensity ρ=900 kg/m3viscosity μ=0.05 Pa-slength =(a)=9 cmdia of…

Q: Consider a desired pump operating condition which adds 35 psi at a flow rate of 500 gpa to water.…

A: Given data Pressure = 35 psi Flow rate = 500 gpm Density of water = 62 lbs/ft^3 Find the pump head…

Q: A 200 kg chunk of lead falls from a height of 30 m and smashes into a rigid concrete floor.…

A: Disclaimer: “Since you have asked multiple questions, we will solve the first question for you. If…

Q: 3. If the flow rate through a 10 cm-diameter wrought iron pipe is 0.04 m'/s as shown in fig below,…

Q: 4 A pipe carrying 200m³/h of water changes diameter from 0.2m to 0.15m through a sudden contraction.…

Q: Q3) How many meters of pressure drop will there be in 1 m length in a horizontal pipe with a…

A: find the pressure drop in 1 m length.

Q: O For the horizontal laminar internal flow through a pipe of diameter (d), if the velocity profile…

A: The velocity profile is- u(r) =-14μdPdLr2-r02 The maximum velocity is -Umax =…

Q: Q1/ For fig shown if water flow rate is 60 lit/s , Find (h) Note that Density: Pwater = 1 kg/m³ Pair…

Q: p1: oil with viscosity (2n10 N.s/) and densily af (850 kg) is Pumped along astraight herizon hal…

A: Given, Density of oil, ρ=850kg/m3Viscosity of oil, μ=2×10-2 (Ns/m2)Discharge,…

Q: Water (SG=1) flows through the diverging frictionless pipe shown at flowrate of Q with the given…

A: Given data as per questionQ=500 m3h=0.1388 m3sP1=500Kpaz1=3mz2=14mD1=400 mmD2=500 mmwe know…

Q: A swimming pool W by Y by h deep is to be emptied by gravitythrough the long pipe shown in Fig. .…

A: Given data: *The bottom dimension of the pool is W by Y. *The depth of the pool is h. *The average…

Q: consider the flow of water (40°) in a pipe, the velocity profiles at the inlet are those shown in…

Q: Compute the head loss and pressure drop in 80 m of horizontal 150-mm-diameter asphalted cast-iron…

A: Detailed answer given in attached file kindly refer it.

Q: 3. Sketch the shear stress and velocity distribution for laminar flow across a pipe section.

A: Consider R to be the radius of the pipe. The expression for the velocity from the center of the pipe…

Q: DETERMINE THE PRESSURE TO HAVE A DISTANCE: 600m CONSISTENT AND COMPATIBLE FLOW RATE Raver ELEVATION:…

A: Given: Total length of the pipe: →L=600 m Height of the water tank from the river surface: →H=100 m…

Q: A large pressurized tank is filled with air discharges into the atmosphere The flow path is a short…

A: Given Data : dnozzle=0.015mTatm=200cPatm=101…

Q: y the help of a fan ,air is drawn through a pipe of diameter 0.5 m. The temperature of air is 20°c…

Q: Water steadily through a reducing pipe bend. Krown conditions are p1 850 3 kPa atsolute, D1 -25 cm,…

Q: The horizontal V fitting, steady, uniform flow at each section, incompressible, and neglect weight…

A: Let us find the velocities at 1 and 2 - Q=A1V1 =A2V20.4=π4201002V1=π481002V2V1=12.73ms, V2=79.577ms…

Q: Jet water in Pipe with chameter equal to Somn to velocity-30 - divided into two branches with…

A: The velocity will remain the same in both the pipes. V=V1=V2 Now,

Q: In the Fig Shown, the Flow rate Pipe (A) is equal ( GA=25 Lit15), the diameter is equal ( DA - 75…

Q: Q2: Water (p-999/kg m3 u 1.16 10 Pa s) flows inside a steel pipe 25cm diameter. 450m length and…

Q: A smooth pipe has an inside diameter of 28 mm, is 16 m long, and carries 10C water at a rate of 8…

Q: 2. For a piping system as shown in the figure, determine the distribution of the water flow Qi and…

Q: A pipeline of constant diameter 0.6m, with its centreline on a horizontal plane turnsthrough a…

A: The objective of the question is to calculate the horizontal components of force exerted on the pipe…

Q: Please answer me in 30min plz urgent need Water enters a 6cm internal diameter thin walled pipe with…

A: Given details: d=6 cmTi=10° CT0=50° CQ=2.3 Lμ=0.798×10-3 Ns/m2k=614.145×10-3 W/mk∆T1=80°C∆T2=40°C

Q: Water (density 1000 kg/m) flows through an inclined pipe of uniform diameter. The velocity. pressure…

A: According to information we have A sloping pipe of a uniform diameter flows through water (dansity…

Q: Consider water flow through a pipe 6 m long and internal diameter 300 mm. The head loss due to…

A: Length of pipeL=6mDiameter of pipeD=300mm=0.3mhead loss due to frictionhf=6mValue of surface…

Q: Consider water flow (40-C) in a pipe, the profiles of speed at the inlet and outlet are shown in the…

Q: re, a flow rate of 2 m3/s is active in a pipe, as seen in the attached figure. What is the expected…

Q: Three pipes A, B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows:…

Q: Two reservoirs, A and B having elevations 250 m and 100 m, respectively, are connected by a 250-mm…

A: For solution refer below images.

Q: For the horizontal laminar internal flow through a pipe of diameter (d), if the velocity profile (r)…

A: ζ = f8ρV2f = frction factorρ= densityV = avg. flow velocity

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Given

VIEW

Solution

VIEW

Page 2

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

What’s the answer for this please ?
Water (density 1000 kg/m?) flows through an inclined pipe of unform diametar. The velocity. pressura and elevation at section A are V, = 3.2 mis, p, =186 kPa and 2, = 245 m respectively, and those at section B ara V = 3.2 /s, py = 260 kPa and 2y = 9.1 m, respectivoly. If accaleration due 1o gravity /s 10 m/s* then the head lost due to friction is ‘m (round off 1o one decimal place).
I need the answer quickly
Fast pls i will give u like for sure solve this question correctly in 5 min pls A reduced bend in a pipe is used to divert the flow of water (p=1000 kg/m³) at a rate of 35 kg/s. The discharge of the fluid is to the atmosphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the outlet. The elevation difference between the centers of the exit and entrance is 40 cm. The mass of the cubit and the water it contains is 60 kg. The center of mass of the fluid assembly and elbow is located 50cm horizontally, with respect to the flange. Consider a flow correction factor of n=1.04 for eq. of linear momentum. Determine: a. The pressure at the entrance of the elbow. b. The net anchorage force in the flange required to hold the elbow in place. c. The moment generated in the flange from the applied forces
Find the head lost due to friction in a pipe of radius 20 cm and length 50m, through which oil is flowing at a velocity of 5 m/s using (a) Darcy formula (b) Chezy formula for which C= 65, Take Specific gravity of the oil is 0.8 and Dynamic viscosity is 8 X 10-3 poise.
In a fully developed turbulent flow through a pipe, the shear stress is……… Please fill the blank correctly.
with a head loss of 7.5-m. Use iterative method to find the pipe diameter requires to keep a flow Q3: Oil, with (p- S950 kg/m'; v 2x10s m2/s), flows through horizontal smooth pipe of 80-m long rate of 0.332 m/s steadily flowing, (Start with initial guess of friction factor f-0.01)
A necked-down section in a pipe flow, called a venturi,develops a low throat pressure that can aspirate fluidupward from a reservoir, as in Fig. UsingBernoulli’s equation with no losses, derive an expressionfor the velocity V 1 that is just sufficient to bring the reservoirfl uid into the throat.
Please send me answer of this question within 10 min i will give you like sure.