C2. A circular pipe 1 of 535 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters 325 mm If the average velocity of pipe 1 and pipe 3 are 4.7 m/s and 3.85 m/s and the flow rate of pipe 2 is 1/3rd water flow in pipe 1. and 180 mm respectively as shown in figure below. V2 D2 Pipe 2 Pipe V3 -D, Find the following: (3 Marks) O Flow rate of water through pipe 1 in m³/s (m Velocity (V) of pipe 2 in m/s (i) Flow rate of water (Q3) through pipe 3 in m/s

C2. A circular pipe 1 of 535 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters 325 mm If the average velocity of pipe 1 and pipe 3 are 4.7 m/s and 3.85 m/s and the flow rate of pipe 2 is 1/3rd water flow in pipe 1. and 180 mm respectively as shown in figure below. V2 D2 Pipe 2 Pipe V3 -D, Find the following: (3 Marks) O Flow rate of water through pipe 1 in m³/s (m Velocity (V) of pipe 2 in m/s (i) Flow rate of water (Q3) through pipe 3 in m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

C2. A circular pipe 1 of 480 mm diameter branches into two pipes (pipe 2 and pipe 3) of diameters 300 mm and 185 mm respectively as shown in figure below. If the average velocity of pipe 1 and pipe 3 are 5.45 m/s and 3.7 m/s and the flow rate of pipe 2 is 1/4th of water flow in pipe 1. V2 Pipe 2 D2 Pipe 1 D, Pipe 3 3 D3 Find the following: (3 Marks) (i) Flow rate of water through pipe 1 in m³/s (ii) Velocity (V2) of pipe 2 in m/s (iii) Flow rate of water (Q3) through pipe 3 in m³/s
4. The pipe system shown in the Figure. The flow rate in pipes AB and FG is 0.88 n³/s. All pipes are concrete. Find the flow rate in pipes BCF, BDF and BEF. 2440 m 500-mm diameter B 0.880 m/s G 1500 m 400-mm diameter 0.880 ms 3200 m 300-mm diameter
Three pipes of lengths of 800 m, 500 m and 400 m and of diameters 500 mm, 400 mm and 300 mm respectively are connected in series. If this compound pipe is to be replaced by a single pipe of length of 1700 m, find the diameter of this single pipe for the same discharge.
Water flows from a 20-mm-diameter pipe with a flowrate Q as shown in the figure below. What is the approximate diameter of the water stream, d, in units of cm, if the distance below the faucet is, h=2 m, and Q = 0.003 m³ /s? 20 mm O a. 1.83 m b. 2.07 m O c. 3.29 m d. 4.66 m O e. 5.29 m
A large artery can have a diameter of about 0.5 cm, whereas a large vein may have a diameter of about 0.8 cm. The average blood velocity in these arteries and veins is, respectively, on the order of 40 and 20 cm sec-¹. Calculate for these blood flows the wall shear rate, Yw. What would the shear rate be at the centerline of these blood vessels?
3. The below figure shows a pipe with a circular cross section of diameter D mm on the left end and a square cross section with side D mm on the right end. Mercury enters the left end with a velocity 1 cm/s and leaves the right end with a velocity V2. Find V2 (neglect losses in the pipe). Inlet Outlet Cannot be find since length is not given Cannot be find since diameter is not given а. b. 7.85 mm/s 12.73 mm/s с. d.
Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f 610 0.020 488 0.032 1220 0.024 A B C Water Figure (3) EL=7om R 152 102 203 B с EL. 15m
The diameter of a pipe at the larger end is 0.6 cm and at the smaller side is 0.3 cm the larger and smaller ends are located 8 meters and 4 meters, respectively, from a datum line. If at the larger end the velocity is 1.2 meters pee second and the pressure is 5300 kN/m^2, compute the pressure at the smaller end
OFICUL Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 0.020 B 488 102 0.032 C 1220 203 0.024 Good Luck - (2) Water qure (3) EL=7om A B EL-15m
The branched pipe as shown in figure below discharges water. The diameters of the pipe 1 is 1.5 cm, pipe 2 is 3 cm & pipe 3 is 4 cm. The discharges in pipe 1 is 21 lit/sec, pipe 2 is 26.25 lit/sec. Find the discharge in pipe3 in Lt/sec, velocity in pipe 2 m/s & velocity in pipe 3 if the diameter of pipe 3 is 4 cm. (ENTER ONLY THE VALUE IN THE BOXES BY REFERRING THE UNIT GIVEN IN BRACKET. ALSO UPLOAD YOUR HAND WRITTEN ANSWERS IN THE LINK PROVIDED) Pipe 1 Pipe 3 Pipe 2 The discharge in pipe 3 (in Liter/sec) = The velocity of water in pipe 2 (in m/s) = The velocity of water in pipe 3 (in m/s) =
For the series-parallel system shown in figure, all pipes are 8cm_diameter cast iron. If the total flow rate is 0.026 m3/s find; a-) The flow rate for each pipe b-) Pressure lost between point (A) and (B) note: Take f=0.02 and neglect minor losses.
reservoir A is at elevation 90 m above datum, furnishes water to a 600 mm pipe which leads to a point at elevation 30 m, the pipe being 610 m long. Here it branches into three pipes, 200 mm, 300 mm, and 150 mm diameter. The 200 mm pipe runs 300 m and discharges to reservoir B at elevation 75 m, the 300 mm runs 450 m to reservoir D at elevation 30 m. f=0.012 what is the rate of flow towards reservoir B most nearly gives?