solve question 4 Q4) Show the instruments and the procedure used to test the concentricity of thespindle and the parallelism of the table for the CNC milling machine.Q5) If the spirit level used for testing the parallelism of the ways of the turningmachine reads .4 mm.a) Show what the spirit value means?b) If the ways of the turning machine show lack of parallelism, how this can affect theworkpiece?Q6) For the presented figure:a-What is the accuracy of the vernier caliper.b- What is the value of the part diameter.Q7) Choose the correct answer for the following sentences:1- The following vernier bevel protractor reads:a-45° 45'b- 52° 15'c-42° 45'-60845301515ppd643650Od- 53° 45'

Disclaimer:“Since you have asked multiple question, we will solve the first question for you that is…

Answered: Q4) Show the instruments and the…

Q4) Show the instruments and the procedure used to test the concentricity of the spindle and the parallelism of the table for the CNC milling machine.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2 Find T= For when 9₁-KADI L
If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the Tape Length Find the Tape Length in mm=
Find y shown in Figure below. 3 cm 0.5 cm - 0.5 cm 1 cm A B 0.5 cm 6 cm -Xc 0.75 cm E 0.75 cm 0.75 cm- e 0.5 cm 2 cm F.
42 in 64 [in]- 50 in D 59 in B این دو سال است اند اما او شده از این سامانه 63 in -10 in 21 in ( Given: The plate( The shaded rectangular volume) has weighs 240 lbf. It is. suspended bycable CD, Which D is wall anchor. So, Find the magnitude of force in the cable CD such the system is in static equilibrium??. Show all works.
Find the moment about point 0 in figure 2 ? I need answer within 10 minutes please please with my best wishes
Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
Q3- Solve the equation for x value :- 1- In e + 4-2log4 x 1 - log5 25
%3D Consider for the part in the figure below, a =112, b= 60 and c= 104. b. b 40 80 20 45 Dimensions in mm Analyze the part in order to calculate the coordinates of the centre of gravity in the (z, y, z) system of coordinates. It is essumed that the following process was following for the manufacturing process • Part 1(a cubic piece of dimension 37 x 60 x 60 is cut out of a Part 2 of dimensions 149 x 60 x 80 and then • Part 3 (triangular prism) is welded Part 2
Exercises: find the solutions of: y² + y = - 6x Ô ý - y = 2x (2sinx ty cosx) 8 ⑨-'=x lo y" + y² - 4 y²- 4y = 32 ³² - 4x-6. -3x
Q2. A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected while the direction of the launching velocity at B and the orientation of the underneath ground are 30° and 40° from a horizontal axis x, respectively, determine: (a) the launching velocity of the skier at B using the formulation of conservation of energy. (b) the distance, s where the skier lands at C by considering motion in x and y axes.
Please solve for 4.139 thx
q1