Pls.help with 24. Question 24In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find thedistance between the pivot and the center of mass for the crane arm (including winch).T2 = 4500 NLocation of center of massfor am of crane53PivotT1 = 650 N2 m6 m A winch mounted at the end of a crane arm is lowering a block of concrete on a cable. The tension in thecable is T1 = 650 N. The crane arm is supported by a second cable that pulls up on the arm at an angle of53° with respect to horizontal. The center of mass for the crane arm (including the winch) is marked with anx on the diagram.T2 = 4500 NLocation of center of massfor arm of crane53PivotT1 = 650 N2 m6 mFind the torque (magnitude and direction) exerted on the arm by the support cable (about the pivot point).

Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find the distance between the pivot and the center of mass for the crane arm (including winch). T2 = 4500 N Location of center of mass for am of crane 53 Pivot T1 = 650 N 2 m 6 m

Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is 100 kg, find the distance between the pivot and the center of mass for the crane arm (including winch). T2 = 4500 N Location of center of mass for am of crane 53 Pivot T1 = 650 N 2 m 6 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The length of a workpiece is 5.25 in. is tapered in the lathe. If the shafting has .035 taper per…

A: GIVEN DATA- LENGTH OF WORKPIECE = 5.25in. TAPER PER FOOT = 0.035 WE HAVE TO FIND AMOUNT OF OFFSET

Q: 45) Find the RPM for turning a 1 1/4 inch shaft on a lathe with the material having a cutting speed…

Q: a.) In a drilling operation, 3 blind holes needs to be drilled to a depth of 16 mm and a diameter of…

A: Note: As per Bartlebyanswering guidelines in case of multiple questions, only one question needs to…

Q: In a lathe machine,tail stock on the lathe bed forms a pair

A: lathe machine - It is a machine that rotates the workpiece about an axis of rotation with the help…

Q: 18. Lathe sizes are usually designated by the. Select one: a.LENGTH OF THE BED b.LENGTH OF WORK…

A: lathe sizes are usually designated by - Distance between centers swing over bed

Q: Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle…

A: Given details: Cutting speedVc=16meter/minSpindle speedn=275rpmformula used : Vc=πdn1000

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: 1. The . . tool is used to draw the cutting plane line arrowheads in AutoCAD .... a. spline fit b.…

A: 1) d) polyline 2) c) revolved 3) b) partial 4) b) half

Q: )Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given d=22mm=0.022m spindle speed N=210rpm

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: 16. The feed rate unit on lathe machine is a. Millimeter per second b. Millimeter per stroke…

A: Feed rate units depend on the motion of the tool and workpiece; when the work piece rotates…

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

Q: Calculate the drawbar hp required to pull a plow with 3X14-in bottoms at the rate of 3.25 mph if the…

A: To Find : The drawbar hp required to pull a plow. Given : The specific draft is 8 psi The depth of…

Q: In the following milling method, metal is cut by a cutter rotating in the same feed direction of…

A: Ans- b. Down milling.

Q: A cylindrical casting of diameter 200 mm and height 100 mm is to be casted. From the previous…

Q: Choose the right answer - In turning, the cutting force that increases by decreasing depth of cut…

A: In turning operation the cutting force is the resultant of tangential force, feed force, and radial…

Q: M 70 bar WXH Tubo de 4 ton C = 75 cm

A: given; weight of tube=4 tons =39226.6Npressure(P)=70 bar =70*105…

Q: A mandrel or steel rod is used to produce in drawing process.

A: Solution:

Q: the net engine power of a tractor is 35 HP, what is the approximate power available at the drawbar?

Q: Convert a speed of 850 rpm into surface speed mm/a. Spindle diameter = 200mm.

Q: Find the spindle speed in rpm, if the slotting operation is performed by 14mm end mill with a…

A: Given data Mill diameter (d) = 14 mm = 14 x 10-3 m Cutting speed (v) = 16 m/min

Q: 5. Lathe bed is usually made of: a) Structural steel. b) Stainless steel. c) Cast iron. d) Mild…

Q: Describe cause, effect and remedy of water hammering

A: Water hammering In a pipe, water is travel with very high velocity. and this velocity of water is…

Q: 6. Approximate a spindle speed of 1000 rpm into rad/s. Spindle diameter = 200 mm 2.25 rad/s .16 mm/s…

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given data spindle speed (N) = 260 rpm end mill dia (d) = 22 mm = 0.022 m To determine Cutting…

Q: To draw a line, select the line tool and tl Draw the line y=(1)/(2)x+6

A: Giveny=12x+6

Q: QUESTION 1 Calculate the spindie speed in RPM of a lathe turning a 96 milimeter diameter material…

Q: To make 5 aluminum wheels with smooth surface and precise dimension as shown in Figure 1 for one…

A: It is given that the final product should possess smooth surface finish and precise dimension.

Q: QUESTION 1 Calculate the spindle speed in RPM of a lathe turning a 96 milimeter diameter material…

A: Given:d=96 mmV=148 SMPM

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

Q: Find the end mill diameter for slotting operation by a cutting speed of 18 meter /minute and spindle…

Q: 1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel…

A: Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three questions.…

Q: Ⓒ80 A part is required to be machined to match the drawing illustred in figure 15 marks QB,…

A: please refer handwritten solution

Q: Taper turning is performed on a mild steel specimen, using the given data determine the following. )…

A: The most common lathe machining operation is turning. A cutting tool removes material from the…

Q: A lineshaft runs at 380 rpm. A 18 inches pulley on the same shaft is belt connected to a 12 inches…

A: A schematic of the arrangement can be drawn as shown below: Let us represent the diameter and the…

Q: The name of this machincal drawing

A: Given Data : Mechanical drawing

Q: How many passes will it take to reduce the diameter from 5 4 (five and one fourth) inches into 3 ¾…

Question

Pls.help with 24.

A winch mounted at the end of a crane arm is lowering a block of concrete on a cable. The tension in the
cable is T1 = 650 N. The crane arm is supported by a second cable that pulls up on the arm at an angle of
53° with respect to horizontal. The center of mass for the crane arm (including the winch) is marked with an
x on the diagram.
T2 = 4500 N
Location of center of mass
for arm of crane
53
Pivot
T1 = 650 N
2 m
6 m
Find the torque (magnitude and direction) exerted on the arm by the support cable (about the pivot point).

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4. The drilling speed for cast iron is assumed to be 70 ft/min. Find the time required to drill two holes in each of 500 castings if each hole has a diameter of 3/4" and is 1" deep. Use .010" feed and allow 14 minute per hole for setup. Page #
Find the end mill diameter for slotting operation by a cutting speed of 16 meter /minute and spindle speed of 295 rpm. End mill diameter in mm =
8. is used most frequently when lifting or setting down loads, but they also occur in carrying, stocking, pushing, pulling, rolling, sliding and wheeling of loads.
10
08. Name the machine below and the part name with labels 1-5 3. Items: 1. Machine name:. 1. ..... 2. .... ..... 2- 4. ..... 5. 2. Operation perform by the machine: 1. 2. USF 3. 4. 5. 4. With the aid of sketches, Explain any two operation showing the cutting condition.? 3.
In a lathe machine the cutting tool has a diameter of 1.6 cm is subjected to a cutting force of 250 N. Compute and identify the nearest value of work done per revolution of the spindle. a. 12.57 Nm. b. 36.88 Nm. c. 23.98 Nm. d. 58 Nm.
Q6: A-List the characteristics of screw thread. B- Calculate the change gears for cutting 16 thread per inch on a lathe having a lead screw of 6 thread per inch?
Solve it fast
9) Down milling operation is performed for finishing cut. Select one: True False
TYPEWRITTEN ONLY PLEASE FOR UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS. I'LL DOWNVOTE.
It is required to cut screw threads of 2 mm pitch on a lathe. The lead screw has a pitch of 6 mm. If the spindle speed is 60 rpm, then the speed of the lead screw will be.
B3