Solve for the mobility.

Q: A motor operates at 1800 RPM and expends 2 HP.  How many ft-lbs of torque does it provide at that…

A: Given data: The speed of the motor is; N=1800 RPM. The power of the motor is; P=2 HP.

Q: 2. The system of figure has degrees of freedom. ---- --- Fork Joiet Two Three Four Soring Slider…

A:

Q: Q1/ A. Write the force system for each one of the following? JIL

A: Given:-  To Find:-  Type of force system

Q: Derive the tension ratio of the belt drive.

A: let T1=tension in belt on tight sideT2=Tension in belt on slack sideθ=angle of contact in…

Q: Direction. Draw the Force Sody Diagram of he tollowing iustrations. Lund

A: Draw the free body diagram for the given figures.

Q: What is the distance between the axles of the two pulleys?

A: Given that: diameter of smaller pulley = 250 mm diameter of larger pulley = 500 mm wrap angle = 120…

Q: Find the distance traveled by the slider if connecting rod is 10 inches, cranks is 30 deg (past top…

A:

Q: Find to the nearer thousandth inch the circumference of the ring that fitsaround this piston for a…

A: Given    Diameter, d = 0.8 in

Q: 01/ Give the dimensions for the hole and shaft for the 12 mm electric motor sleeve bearing (pump);

A: Given:Basic size given for motor sleeve bearing=12 mm

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: A team of professional thieves wants to knock down a castle wall using a primitive explosive. At…

A: Given: total mass of the explosive(M) = 40 Kg and it breaks into three pieces as shown below:

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: 2) Compute the effective inertia that a clutch must transmit to accelerate a 54-inch solid shaft…

A: Introduction: The ability of a body to resist angular motion about an axis is defined as its moment…

Q: Need help on all questions. Please include all units, steps to the problem and information such as…

A:

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Please solve for the reactions at A

A:

Q: Question 24 In the same setup as in question 23, if the mass of the crane arm (including winch) is…

A: Solution for Question 24: Given, Mass of arm = m = 100 kgWeight of arm = W = mg = (100) (9.81) = 981…

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: (x(x+ y) = y(x – y) By homogenous equation solve %3D

A: DE1 (3x2y + 2xy + y3)dx + (x2 +y2)dy = 0 so, M = (3x2y +2xy +y3)  and N = (x2 +y2) dMdy=3x2 + 2x…

Q: find the fbd solution

A:

Q: Solve 0.782bar in p/q form

A: Given that : x = 0.782782782....... We need to find it in the form of p/q

Q: 4. Determine the length of stroke of a slider E when the crank AC rotates by 30 degrees in counter-…

A: Find the attachment for the solution.

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: ths angle of the three forse acting on hook

A: given: determine the resultant and the angle of the three forces acting on hook?

Q: Determine the horizontal and vertical stroke of a slider D and F when crank AB rotates 30 legrees…

A:

Q: 3-9. Solve for the algebraic sum of the moments in pound-feet about A when h is 20 m as shown in…

A: Given data h = 20m Forces acting are 800N, 500N

Q: The objects shown below have been rotated positively about one of the axes shown. the amount of…

A: According to the given data rotation amount and rotational axis is provided in the below picture.

Q: - following mecha

A:

Q: to move a force of 1713 lbs using a 100 psi what size bore in diameter would it need in inches

A: Given data: F=1713 lbsσ=100 psi Need to determine the size bore in diameter.

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: During the governor regular working time the sleeve moves up with 16mm due to the effort of 225N…

A: Given that, The effort of the governer, F=225 N and the movement of the sleeve is, x=16 mm=0.016 m,

Q: If an inlined plane has an IMA of 8, an output force of 160N and an input force of32oN what is the…

A: Given Data:To Find: IMA: Ideal Mechaincal AdvantageAMA: Actual Mechaincal Advantage

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: Explain newtons third l

A: for every action their is equal and opposite reaction.

Q: A pulley system is combined with an inclined plane. The pulley system has an IMA of 3, an efficiency…

A: Given data: IMA = 3 The efficiency of the pulley system, ηpulley=96% weight of the box, W = 215 lb…

Q: The punching machine is using the flywheel for its smooth running operation. The flywheel running at…

A: Given data: Convert the “rps” into “rpm” as follows: