Q2)Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the mainpower supply of (220 Vrms). Find: -1- The transformer turns ratio (a).VOlvolt)2- The ripple voltage.Vm = 12 V3- The Vdc value.4- The RMS value of the output voltage.V(p.P)= 0.1 V5- The ripple factor.6- The value of capacitor filter.(assume ideal diodes)T = 0.01 sec.→ t(sec.)

Average output Voltage: Vo=1π∫0πVmsinωtd(ωt)=2Vmπ Vm=Maximum output voltage of Secondary side RMS…

Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Vo volt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p-P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T= 0.01 sec. t(sec.)

Q2) Design a Bridge FWR to supply a load of (1002) with the waveform shown in figure from the main power supply of (220 Vrms). Find: - 1- The transformer turns ratio (a). Vo volt) 2- The ripple voltage. Vm = 12 V 3- The Vdc value. 4- The RMS value of the output voltage. V(p-P) = 0.1 V 5- The ripple factor. 6- The value of capacitor filter. (assume ideal diodes) T= 0.01 sec. t(sec.)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Pls answer d. Only
A 500 MVA synchronous machine has H, = 5.6 MJ/MVA and a 1200 MVA machine has H₂ = 2.0 MJ/MVA. The two machines operate in parallel in a power station. What is the equivalent. H constant for the two, relative to a 100 MVA base?
Design a CT-FWR to supply a load of (502) with a waveform of the following specifications: - • Vdc = 12 V • Ripple factor = 0.1 % • the main power supply is (220 Vrms, 50 Hz). Determine the following values: - 1- The value of capacitor filter. 2- The maximum load voltage (VmR) 3- The transformer turns ratio (a). 4- The RMS value of the load voltage. 5- Draw the output waveform. (assume ideal diodes)
B1. The sinusoidal waveform is displayed by the CRO is shown in Figure below. The 'time/cm switch is on 10 ms/cm and the volts/cm' switch is on 10 V/cm. Calculate (a) the frequency, (b) the peak to peak voltage, (c) the amplitude (d) the r.m.s voltage.: The frequency is = The peak to peak voltage is = The amplitude is = The r.m.s voltage is =
Please solve in 25 minutes, please
In single phase fully controlled converter, if the form factor is 4.75 then the ripple factor of the converter is
Construct the circuit in Figure 1 in the Circuit JS simulator. Note that the voltage source is given in RMS. Within Circuit JS while defining the max voltage of the voltage source include “rms” after the number to tell Circuit JS that this is a rms value. Also note that there are additional parameters when instantiating a transformer in Circuit JS. Leave these at the default values. Additionally, transformers may have problems simulating in Circuit JS. Answer the following: 1. From the simulation results, determine the power dissipated in R2 and compare to the expected value from the previous section.2. Change the transformer ratio (“Ratio” as a fraction when you “Edit…” the transformer component) to the value calculated in the previous section to provide maximum power transfer in R2. Note: In Circuit JS, Transformer Ratio = Primary/Secondary.3. Rerun the simulation, calculate the power dissipated in R2 and compare to the expected value from the previous section.4. Change the…
how to measure ripple factor and peak input and peak output voltage for this circuits ?
Efficiency at full-load and half the full-load at 0.8 p.f. lagging current. Equivalent reactance referred to primary & referred to secondary..........ohm , ..........ohm Equivalent resistance referred to primary & referred to secondary..........ohm , ..........ohm Regulation of transformer at 0.5 p.f. lagging current The magnetizing current and reactance component of no-load are.........amper , .........ohm The working current and resistance component of no-load are.........amper , .........ohm *
4. A DC/DC step down converter is supplied by 96 V DC supply and produces average 24 V DC output. The switching frequency is 1 kHz, Al = 10 A, R=16 Ohm a. Draw equivalent circuit and obtain the duty cycle and the value of inductance. b. How do you reduce the voltage ripple below AV=5 V.
Topic- basic & const.