FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondaryvoltage is Vs = 42V and output power of the transformer is PN= 2750W.The value of loses powers are Pcu = 52,5W and Pre = 39W. The resistance of loads are RLI = 1,660 andR12 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determinethe following values in the circuit:PrimarywindingSecondarywindingN, turnsNg turnsMagneticFlux,PrimarycurrentISLSecondary4 currentPrimaryvoltageISL1(ISL2SecondaryvoltageRL1R12TransformerCore(a) the primary voltage VP,(b) the secondary load current Isı, if the transformer is rated at RLI and R12,(c) the primary load current IpL,(d) the load resistance R13 when the transformer is fully loaded by third in parallel,(e) efficiency n (fully loaded)

(a) In the question following data is given Np=720 Ns=144 Vs=42 volt Vp can be found by following…

FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondary voltage is Vs = 42V and output power of the transformer is Py= 2750W. The value of loses powers are Pcu = 52,5W and PrE = 39W. The resistance of loads are RL = 1,660 and RL2 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit:

FN.Q5 – A Transformer has primary windings as Np = 720 and secondary windings as Ns = 144. Its secondary voltage is Vs = 42V and output power of the transformer is Py= 2750W. The value of loses powers are Pcu = 52,5W and PrE = 39W. The resistance of loads are RL = 1,660 and RL2 = 1,950. (Pcu and PFE will be considered to be approximately the same in different load values.) Determine the following values in the circuit:

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question-4: In the bridge type circuit shown below, the diodes are assumed to be ideal. The transformer is specified to have a 15 Vems secondary voltage. Find: A- D.C. output voltage Vpco B- Peak inverse voltage PIV. 1:4 +100 V . ov -100 V
Q2 (a) Describe the main difference between ideal transformer and practical transformer with help of figure.
An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
A 200 V/100 V, 50 Hz transformer is to be excited at 40 Hz from 100 V side. For the exciting current to be same, the applied voltage should be ?
A 20 kVA, 2000/200-V, 50-Hz transformer has a high voltage winding resistance of 0.2 2 and a leakage reactance of 0.242. The low voltage winding resistance is 0.05 2 and the leakage reactance is 0.02 2. Find the equivalent winding resistance, reactance and impedance referred to the (i) high voltage side and (ii) the low-voltage side. (Draw the related equivalent circuits)
For the following circuit if the secondary voltage of the transformer is 25V rms, the PIV of the diodes are 888 leeeeeeeee V₂ HF C₁ D₁ C₂ HE 2V + D₂ ZVm +1f C3 D3 + C₂ +6 2V 55 V 35 V 56.56 V 72.7 V O O O O
An ideal transformer circuit is shown in Figure Q4(a). Its primary and secondary turns are 400 and 200 respectively. (1) Calculate the rms primary current. (ii) Calculate the rms flux in the transformer core. (iii) State two losses that contribute to transformer active power loss that have been ignored in this ideal model. N, Ny 30 + j30 2 300 sin50t Figure Q4(a) 00000000
Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
SOLVE STEP BY STEP IN DIGITAL FORMAT XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX 2. A transformer with a 10/1 turns ratio has a maximum flux density of 60,000 lines/in2, when the primary winding is connected to a 2300 V power supply at 60 cps. What will be the maximum flux density if the secondary is connected to a 115 volt supply at 25 cps with the primary open?
A transformer having a nominal voltage = 399V and a no load voltage = 420V at its secondary, the short circuit current at the secondary of this transformer in function of its nominal current will be: Select one: Isc=10*In None of these Isc=30*In Isc=20*In Isc=40*In
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
The EMF equation of transformer referring to primary turns is Select one: O a. 4.440N,B O b. 4.440 fN. mi OC. 4.440 N,A O d. 4.440 fN,