Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of the thyristors T1 and T2 is equal to 110° and that T3 and T4 have similar firings in the negative half-cycle of Vs. a)Sketch the output voltage waveform for a highly inductive load. b) Sketch the waveform output voltage, replacing the highly inductive load with a purely resistive load. c) Get the value of the average output voltage when the load is purely resistive.

Given the circuit in Figure 04 and defining that: Vs = 100 sin (wt) Volts and the firing angle of the thyristors T1 and T2 is equal to 110° and that T3 and T4 have similar firings in the negative half-cycle of Vs. a)Sketch the output voltage waveform for a highly inductive load. b) Sketch the waveform output voltage, replacing the highly inductive load with a purely resistive load. c) Get the value of the average output voltage when the load is purely resistive.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A buck converter is working in a steady state. The output voltage and the inductor current can be assumed to be ripple-free, The inductor voltage v during Ton is 50V and during Toff is 3OV. Assuming all devices are idea then: What is the input voltage? Answer: 70
AC 15. What would the equivalent resistance be of a 159 uF capacitor? 16. What is the RMS voltage of a circuit if the peak voltage is 170 volts? 17. If the RMS voltage is 240 volts AC, what is the peak voltage? 18. What is the formula for finding an inductors equivalent resistance? 19. What is the equivalent resistance of an inductor with 0.17 henrys? 20. What is the symbol of an AC power source? 21. What is the equivalent inductance of a parallel circuit with a 0.01L, 0.02L, and 1.7L inductor? 22. What is the equivalent inductance of a series circuit with a 0.03L, 0.04L, and 1.6L inductor? 23. A transformer with a primary voltage of 480 volts and a turns ratio of 2:1 will have what secondary voltage? 24. A Power Network is comprised of what three components? 25. What is the main difference between a fuse and a circuit breaker?
Problem 3 For the circuit shown below, assume that: R=20kQ, D1, D2, D3 and D4 are modeled by a battery of 0.8 V and rB = 30Q, the Zener diode has 5 V breakdown voltage and rz= 502. 'Vin' is a sinusoidal signal with 1 kHz frequency and amplitude voltage of 15 V: • Sketch 'Vout' and Iz' for -15V< Vin <15V. • Plot 'Vout' and Iz’ versus time • What is the function of this circuit? Vout w- + + D4 D, Vin D
Problem 3 For the circuit shown below, assume that: R=20k2, D1, D2, D3 and D4 are modeled by a battery of 0.8 V and rB = 30, the Zener diode has 5 V breakdown voltage and rz = 502. Vin' is a sinusoidal signal with 1 kHz frequency and amplitude voltage of 15 V: • Sketch 'Vout' and 'Iz’ for -15V< Vin <15V. Plot 'Vout' and 'Iz’ versus time • What is the function of this circuit? R Vout + + D4 70, Vin D
Power Electronics Question
0) A full-wave controlled rectifier with RL load is shown in figure 8. If the firing angle is 70° and the average load current is 20A, find the transformer ratio (N/N). V,-v2 x200 Sin314 100MH Figure 8 w
6)For the CRO Sine waveform shown in figure, determine (a) Time period, (b) frequency, c) amplitude (d) peak-to-peak voltage and e) RMS voltage.
The current through the diode in the circuit given in the Figure below when Vy = 0.7 V is? ww 8092 12V Select one a. 24.26 mA b. 13.09 mA c. 58.23 mA d. 40.13 mA 40-52 ww 3092 ID
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
i need the answer quickly
Determine the numerical value of the following accumulations: Problem 03.034.d Accumulator output The numerical value of the given accumulation is 3
We want to investigate how the field strength will be with air as dielectric and with steatite. A plate capacitor is placed in a 24 kV network between phase and ground. The relative permittivity of air is &=1 and for steatite &-6. The plate capacitor has area = 1m². The distance between the electrodes is 2 mm. Ep = 8.854-10-12 F/m A=1m² d=2mm a) Calculate the maximum field strength in the plate capacitor. (Answer: 9.8kV/mm) b) What is the capacitance of the capacitor if we use steatite? (Answer: C = 26.6nF)