Q1. Find the heat flow rate through the composite wall as shown in Fig. bele Assume one dimensional flow & the area is variable for each layer. Where: 60°C kA = 152 W/m°C, kB = 31 W/m°C, %3D 3 cm kC = 68 W/m°C and 7 cm %3D kD = 53 W/m °C. 400°C A 10 cm 5 cm 8 cm 3 cm D. BC

Q1. Find the heat flow rate through the composite wall as shown in Fig. bele Assume one dimensional flow & the area is variable for each layer. Where: 60°C kA = 152 W/m°C, kB = 31 W/m°C, %3D 3 cm kC = 68 W/m°C and 7 cm %3D kD = 53 W/m °C. 400°C A 10 cm 5 cm 8 cm 3 cm D. BC

Name: Q1. Find the heat flow rate through the composite wall as shown in Fi
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q1. Find the heat flow rate through the composite wall as shown in Fig. beleAssume one dimensional flow & the area is variable for each layer.Where:60°CkA = 152 W/m°C,kB = 31 W/m°C,%3D3 cmkC = 68 W/m°C and7 cm%3DkD = 53 W/m °C.400°CA10 cm5 cm8 cm3 c

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1. Find the heat flow rate through the composite wall as shown in Fig. below. Assume one dimensional flow & the area is variable for each layer. Where: 60°C kA = 152 W/m°C, kB = 31 W/m°C, cm kC = 68 W/m°C and 7 cm D %3D B kD = 53 W/m°C. 400°C 10 cm 5 cm 8 cm
Q1. Find the heat flow rate through the composite wall as shown in Fig. below. Assume one dimensional flow & the area is variable for each layer. Where: kA = 152 W/m°C, kB = 31 W/m°C, kC = 68 W/m°C and → 60°C :3 cm kD = 53 W/m°C. B 17 cm 400°C A 10 cm 5 cm 8 cm cm
c) Calculate the rise of a liquid of density p= 0.8 g cm-³ inside a square straw, with the cross section given by a square of side L = 2 mm. The surface tension for the solid- liquid interface is st = 200 mJ m-2 and for the solid-gas interface Ysg = 250 mJ m-².
Example: If the temperature gradient is 2ºC per 100 Km and if the specific heat capacity of the air is 0.25 Kcal/Kg.ºC .How much thermal energy per unit mass is convicted to the point P in 12h if the air is moving at a speed of 10KM/h?
1. A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by a fish. Having its temperature constant while it travels from the depth of release to water surface, solve for the following: a. kPaabs when released b. bubble diameter at 60m depth c. bubble diameter at the water surface h2=60m h,=120m SG=1.03
Fast pls i will give u like for sure solve this question correctly in 5 min pls Consider a solid bar of length L with variable cross-sectional area given by A(x) , where x ∈ [0, L] is distance along the bar. If the sides of the bar are insulated and if A(x) varies slowly, it is reasonable to make an approximation in which the heat flows only in the x direction. Consider the rate of change of the total thermal energy between arbitrary positions x = a and b to derive a heat equation for the bar in terms of the temperature u(x, t) . You may assume the density, heat capacity and thermal conductivity are constant (i.e. constant thermal properties) and that there is no heat source.
Topic: Heat transfer Completely solve and box the final answer. 5. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Find the thermal coefficient.
1- Find using Buckingham Theorem the relationship of the effect on pressure drop (AP) (M L-¹T2), of the variables d- pipe diameter (L), 1- pipe length (L), p-fluid density (ML-³) μ- Fluid viscosity (ML-¹T-¹) and V- Fluid velocity (L T-¹). - Assume the input power to a pump P (ML T-¹) is depend on Q- Flowrate (L3 T-¹), H-pump head (L), p-fluid density (ML-³) Create a relation by dimensional analysis between the power and other variables by Buckingham Theorem. Assume the input power to a pump P (ML T-¹) is depend on Q- Flowrate (L³ T-¹), H-pump head (L), p- fluid density (M L-³) Create a relation by dimensional analysis between the power and other variables by Rayleigh Method.
Topic: Heat transfer Completely solve and box the final answer. 6. Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. What is the heat absorbed by the water?
A Classwork for MENG420 - Heat Ti X b My Tutoring | bartleby + classroom.google.com/u/1/w/MTQ3MTM5MDC2NTY3/t/all C E Apps M Gmail YouTube Translate Маps Given-Problems-MENG420-Chapter-7.pdf Mount L Open with ▼ Problem 7.56 Hot water at 50 °C is routed from one building in which it is generated to an adjoining building in which it is used for space heating. Transfer between the buildings occurs in a steel pipe ( k = 60 W / m² .K) of 100-mm outside diameter and 8-mm wall thickness. During the winter, representative environmental conditions involve air at T =-5 °C and V=3m/s in cross flow over the pipe. a) If the cost of producing the hot water is $0.10 per kW.h, what is the representative daily cost of heat loss from an uninsulated pipe to the air per meter of pipe length? The convection resistance associated with water flow in the pipe may be neglected. b) Determine the savings associated with application of a 10-mm-thick coating of urethane ( k = 0.026 W /m.K ) to the outer surface of…
Air is compressed by a compressor in steady-state operation, i.e. the inlet mass flow rate qm is constant in time. The compressor is airtight. The area of the inlet and outlet cross-section is A and AOUT, respectively. The outlet-to-inlet density ratio is PouT PIN the outlet-to-inlet mass flow rate ratio is 9m-OUT/9m-IN- What is the outlet-to-inlet volume flow rate ratio? 9V-OUT/av-IN =? Select one: a. 9V-OUT/av-IN = (A OUT'A IN) (POUT PIN b. 9V-OUT/av-IN = PIN/POUT C. 9V-OUT/av-IN = 9m-OUT/ 9m-IN d. 9V-OUT/av-IN=AOUTAIN
Q3/ Solve ONE only 20 M 1) Find the rate of bubble volume increasing when the radius is 4cm if its surface area is increasing at 47 cm/sec? 2) A cable needs to pass from a station located on the ocean to an offshore facility as given in the Figure. The cable work costs $25/ft to pass through land, and $50/ft to pass under water. How much cable should be pass under water to minimize the overall cost? What is the lowest cost? 1000 ft 5000 ft