Air is compressed by a compressor in steady-state operation, i.e. the inlet mass flow rate qm is constant in time. The compressor is airtight. The area of the inlet and outlet cross-section is A and Aout, respectively. The outlet-to-inlet density ratio is PouT! PIN the outlet-to-inlet mass flow rate ratio is 9m-OUT/9m-IN- What is the outlet-to-inlet volume flow rate ratio? 9V-OUT/av-IN =? IN OUT Select one: a. 9V-OUT/av-IN (AOUTAIN (POUT/PIN) O b. 9V-OUT/av-IN = PIN/POUT C. 9V-OUT/av-IN = 9m-OUT/ 9m-IN = d. 9V-OUT/av-IN-OUTAIN

Air is compressed by a compressor in steady-state operation, i.e. the inlet mass flow rate qm is constant in time. The compressor is airtight. The area of the inlet and outlet cross-section is A and Aout, respectively. The outlet-to-inlet density ratio is PouT! PIN the outlet-to-inlet mass flow rate ratio is 9m-OUT/9m-IN- What is the outlet-to-inlet volume flow rate ratio? 9V-OUT/av-IN =? IN OUT Select one: a. 9V-OUT/av-IN (AOUTAIN (POUT/PIN) O b. 9V-OUT/av-IN = PIN/POUT C. 9V-OUT/av-IN = 9m-OUT/ 9m-IN = d. 9V-OUT/av-IN-OUTAIN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping power with given flow conditions. Discuss the results. Design 1: Tank B 60 m 8 cm I 8 cm Pipe exit 40 m Sharp bend Pump Tank A Dia - 5 cm 18 cm Pipe inlet Sudden expansion 15 m
Vacumm You are designing a vacuum system with a desired equilibrium pressure of 10-7 torr. The turbomolecular pump you are using has a pumping speed of 400 L/s. What is the maximium surface area of the chamber that you can allow, assuming that the outgassing rate per square cm 10-9 torr L/s? Note : total outgassing rate G = ( outgassing rate per area ) * ( area )
35. Water enters a heated tube of 2 mm diameter at 30 C and leaves the tube at 60 C. Find the water mass flow for the average Reynolds number of 1000. [Ans.: 0.00564 kg/s].
dp 1. It shows that the behavior of fluid is A From the equation stated, show the formula for mass flow rate AVp = c. :C.
The pressure of a reactor vessel can be adjusted bychanging either the inlet or outlet gaseous flow rate. Theoutlet flow is kept fixed as long as the tank pressure remainsbetween 100 and 120 psi, and pressure changes are treatedby manipulating the inlet flow control valve. However, if thepressure goes higher than these limits, the exit gas flow isthen changed. Finally, if the pressure exceeds 200 psi, a ventvalve on the vessel is opened and transfers the gas to a storagevessel. Design a control scheme that meets the performanceobjectives. Draw a process instrumentation diagram for theresulting control system
asap
Problem-4: The characteristics for a pump are given in the table below. The pump is required to left water against static head Az = EN" m. The pipe arrangement has a total length L the pump discharge, head, efficiency and power for the given pipe system. 200, d = 0.1 m and f= 0.016. Find %3D Q (L/s) 10 20 30 35 42 50 Hp (m) efficiency % 210 201 180 150 129 93 48 30 58 80 85 86 74 EN=62 Hp = Az + h, = Az + 12.1 d P = 757
A pitot-static probe is used to determine the flow velocity by measuring the differential pressure as shown in Figure 7. The pressure difference sensor used in the system is electronic types and the output of the device is measured in voltage. The output of the pressure device is 3.5 V and the linear relationship between the device and the pressure difference is 10 kPa/v. i. Derive pitot formula to obtain flow velocity from Bernoulli equation, ii. Calculate the pressure difference inside the system, iii. Determine the velocity inside the system if the the fluid is water, and iv. Explain the cause that / ontirbute to inaccurary in the velocity reading. Fluid Flow, V Stagnation Static pressure pressure Pi-P2 Figure 7: Pitot static probe
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
A pump draws water from open reservoir A at 20 ft above pump centerline and lifts to an open reservoir B at 280 ft above pump centerline. The loss of head at the suction is 3 times the velocity head at the 6 inches suction pipe and at the discharge is 20 times the velocity head at the 4 inches discharge pipe. The pump discharge is 200 GPM. a. The total dynamic head in ft. b. The water power in horsepower
2. The initial condition of air in an air compressor is 99 kPa and 30 deg. C and discharges at 438 kPa. The bore and stroke are 374 mm and 395 mm, respectively. The percent clearance of 11 % running at 356 rpm. Find the volume of air at suction in m^3/s ANswer in one decimal places
Assuming the clearance is negligible for a single stage compressor with the following data.Atmospheric pressure: 90 kPaAtmospheric temperature: 17 ˚CDelivery pressure: 7 barFree air delivery flow rate: 0.2 m3/minTake “n” as 1.3, cp = 1.005 kJ/kg K, cv = 0.718 kJ/kg K 1.What is the power input to the compressor in kW to 2 decimal places if the compression is polytropic compression process with n=1.25?