A E D a B a C Bar ABC is supported by a roller at B and a frictionless collar at A that slides on a fixed bar DE. Determine the support reactions at points A and B. Take a = 5in, P = 100 lb.

Q: 2. Which one is essential for combustion of fuel? A. oxygen to support combustion B. proper ignition…

A: Which one is essential for combustion of fuel.

Q: The left-to-right current in the stream causes a uniform drag of 5.4 lb per cross-stream foot on the…

A: Given:Uniform drag = Find:The maximum and minimum tension in the cable.

Q: A container of air is at atmospheric pressure and 27°C. To triple the pressure in the container, it…

A:

Q: A cantilever beam is subject to the loading shown in Figure 1. Use positive convention for the…

A:

Q: 2- A 15 m long, 75 mm diameter riser tube receives saturated water at 160 bar and at a velocity of…

A:

Q: The drive shaft of the motor is made of a material having an allowable shear stress of τallow= 72…

A:

Q: Gears A and B of mass 15 kg and 60 kg have radii of gyration about their respective mass centers of…

A:

Q: A thin rectangular plate that lies in the xy plane is supported by a cable and a bearing at point C.…

A:

Q: A high diver is performing a dive from a 10-meter platform. The diver jumps off the platform with an…

A:

Q: 16-109. Member AB has the angular motions shown. Determine the angular velocity and angular…

A: From given spatial representation of mechanism, points A and D are fixed points. Thus, the points A…

Q: Refrigerant-134a enters the compressor of a cooling system as superheated vapor at 0.18 MPa and 0°C…

A:

Q: 3. Differentiate between the behaviors of metallic and non-metallic materials under tensile test.…

A: 3)In this we have to differentiate between the behaviour of metallic and non metallic under tensile…

Q: How did you get the Tsat values

A: This question is based on the properties of water at different temperatures and pressure.

Q: Problem 77. The pilot of a 90,000 lb airplane which is originally flying horizontally at a speed of…

A: Given:To find:Time average drag force, D.

Q: The force required to tow a 1:30scale model of a motor boat in a lake at a speed of 2m/s is 0.5 N,…

A: Given the force required to tow a 1:30 scalemotorboat speed= 2m/sForce = 0.5NLet's Assume that the…

Q: A ductile hot-rolled steel bar has a minimum yield strength in tension and compression of 50 kpsi.…

A: Given:To find:Calculate factor of safety.

Q: Find the total Force acts on cuvy right tring Plate. as shown infigi 18.9790 1 Water R=3! R=3 b=2m…

A: Water with density= 9790 N/m3other density is R= 3 N/m3To find: Total force

Q: One end of a piano wire is wrapped around a cylindrical tuning peg and the other end is fixed in…

A:

Q: I have been given two questions to solve, the first of the two I solved which is: 'Consider an idea…

A: The effectiveness is .The isentropic efficiency of compressor is .The isentropic efficiency of…

Q: Provide average and instantaneous velocities formulas.

A: We have to determine  the formula for the average and instantaneous velocity.

Q: U= ↑↑↑ B = A = Recr = 5 x 105 C = A boat is moving over fresh water at a speed of 60 km/h. The boat…

A:

Q: Determine the angular acceleration of link AB if link CD has the angular velocity wcD 1.8 rad/s and…

A: The angular velocity of CD is The angular acceleration of CD is

Q: Q.2) For the figure shown, if a load P₁ = 120 kN at A and load P₂ 100 kN is uniformly distributed…

A: Given:Find:Poisson's ratio for the pipe material.

Q: The military jet aircraft has a gross weight of 28,000 lb and is poised for takeoff with brakes set…

A:

Q: The boom is intended to support two vertical loads, F₁ and F₂. If the cable CB can sustain a maximum…

A: The boom is intended to support two vertical loads, F1 and F2 the cable CB can sustain a maximum…

Q: A thin copper rod, 6 m in length, is heated at its midpoint and the ends are held at a constant…

A:

Q: Identify the GD&T applicable for the following component assembly. Make a table including Tolerance…

A: Given:To find:Identify the geometric dimensioning and tolerancing (GD&T) applicable.

Q: 6 in. 8 in. A 8 in. 6 k 10 k 6 k 5 in. 5 in.₁ 8 in. 4 k B 8 k 4 k

A:

Q: 3- A forced circulation boiler delivering 36 kg/s at 130 bar is operated with a circulation ratio of…

A:

Q: The 54-mm-diameter solid shaft is subjected to the distributed and concentrated torsional loadings…

A:

Q: A heating system must maintain the interior of a building at TH = 20°C when the outside temperature…

A:

Q: Identify the zero-force members in the below truss: P₁ A F 3 m- E B 3 m D 4 m 8c+

A:

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the…

A:

Q: Example 2.22: A steel pipe 25 mm internal diameter and 33 mm outer diameter and insulated with…

A:

Q: A 150-g model rocket is fired vertically. The engine applies a thrust P which varies in magnitude as…

A: Given:To find:Time for the rocket to reach its maximum elevation.

Q: Problem 3 - Air Conditioning ( An office building has a window air conditioner with a COP of 2 that…

A:

Q: Calculate the couple moment of the forces.

A: To determine the couple moment of forcesforce exerted by the person in the driving wheel, diameter…

Q: A steady-flow Carnot cycle uses water as the working fluid. Water changes from saturated liquid to…

A:

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the…

A: Given:To find:Thermal efficiency of the cycle.

Q: Two couples act on the frame. If the resultant couple moment is to be zero, determine the distance d…

A:

Q: Example 1: A four stroke design has the following specifications: Brake power = 5 kw, speed = 1200…

A: Write expression for mechanical efficiency.Substitute all known values.Consider the bore diameter as…

Q: A. What is the coefficient of friction for a sphere of radius 0.37 um? (the viscosity of water is…

A: The coefficient of friction for a sphere moving through a viscous fluid like water can be calculated…

Q: Provide at least one example of a truss, one example of a machine, and one example of a frame. Find…

A: It is asked to write about truss, machine and frame with example

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: 3- A forced circulation boiler delivering 36 kg/s at 130 bar is operated with a circulation ratio of…

A: Given data:mass of steam delivered by boiler, ms = 36 kg/sCirculation ratio = 5:1Pressure rise, P =…

Q: What is the coefficient of performance (COP) if the cooling effect is 85,000 Btuh and the power…

A: What is the coefficient of performance (COP).If the cooling effect is 85,000 Btuh and the power…

Q: Derive the following equation? @2 0.622P 82 P₂ - P

A:

Q: Q1) The stress function (x) for the cantilever beam as shown in the figure is given by: $(x) = ² (…

A: Given:To find:

Q: 4-22. Determine the magnitude and direction of force F and its placement d on the beam so that the…

A: Determine the magnitude and direction of force F and its placement d on the beam so that the loading…

Q: R4-5. Replace the force and couple system by an P. equivalent force and couple moment at point

A: Given:To find:Couple moment at P.