Q1) The cantilever beam is subjected to axial load as shown Below, determine the actual stresses acting at points A, B, C and D. 10 AN -- 100 mm 20 kN 15 kN

Q: The beam AEFGB is subjected to the distributed loads, moments and point loads shown. Determine:…

A:

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 15 ເຄດາ -…

A:

Q: For the beam shown below, classify if it is internally unstable, statically determinate, or…

A: Internally stable and Unstable Beam:- A structural system is made up of different structural…

Q: 25 mm 160 mm Ain B 2 m 1m- Im For the beam and loading shown, consider the cross section nn. (a)…

A: Given data: P1=188 N P2=381 N b=25 mm d=60 mm

Q: 2 - For beam I with distributed and concentrated loads, determine:   a)The maximum shear stresses…

A: The FBD of the beam is shown below: Taking equilibrium equation: The SFD of the beam is shown…

Q: 1-6. Consider the loads of Fig. P1-6 to be axially applied at sections A, B, C, and D to the steel…

A: Given:  Cross sectional area of steel bar = 3 sq. in Solution:  (Please refer images below for…

Q: a) Find minimum diameter nceded if the allowabe shear stress is 140 Mpa and the otation of point A…

A: Solution:-  We know that torsion equation is, TJ=τr=GθL here, net torsion is , T=T3-T1+T2  =10-4+2…

Q: - The axial stresses due to bending and axial loads Shear stresses - the principal stresses and…

A:

Q: steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Given:- Span = 4m Simple Supported beam Tensile stress = 35N/mm2  To find:- w, δmax compressive

Q: The cantilevered W530 x 150 beam shown is subjected to a 8.5-kN force F applied by means of a welded…

A: F=8.5kN To find equivalent couple force system at point O

Q: A 22.5 lb/ft ↓↓ 5.0 ft C 250 lb B 0.617 in. 2.269 in. Ⓡ -3.0 ft-

A: given- a cantilever beam  carrying UDL and concentrated load and having maximum tensile stress 4ksi…

Q: Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded…

A: A loaded beam is given and it has been asked to determine location of maximum flexural compressive…

Q: Q- A simply supported rectangular beam having span 5m is subjected to a central point load of 50 kN.…

A: Given- Span=5 m load=50 kN Stress=220 N/mm2,

Q: "D.77. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 21 MPa,…

A:

Q: Determine the forces in each member of the truss. Start to solve from Joint H and also from Joint D…

A: The given truss is shown below.

Q: Q4, Determine The maximum stress Produ ced bn te loads and prtarialu Kiernipur Creat he shear and…

A: Calculate support reaction:

Q: H.W. #4: A pin connected truss is loaded and supported as shown, determine: a) The normal stress in…

A: Determinea. The normal stress in member DE if it has cross sectional area of 750 mm2. b. The minimum…

Q: the rectangular beam given in figure below has been designed for flexure; design the necessary shear…

A: It is required to determine the factored load. wu=1.2DL+1.6LL=1.240+1.625=88 kNm It is required to…

Q: Q-A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given Internal diameter Di = 40 mm Outer Diameter Do =100 mm Number of revolution per minute N = 120…

Q: Q2: Compute the value of ultimate load (Pu) in term of Nominal moment Mn, Steel Section is W18x76…

A: solution     Since Ds of the structure is 4-2=2so minimum hinges required for…

Q: A steel beam of I cross-section is simply supported on a span of 4m. Find the safe uniformly…

A: Consider the free body diagram;

Q: A pipe column is braced to prevent bending and buckling. It is subjected to a compressive load of…

A:

Q: stress Oy in ksi). Both ctor of safety of FS = N te shear failure. De - See table to comp

A:

Q: C): -The rigid bar BDE is welded at point B to the rolled-steel beam AC. For the loading shown,…

A: Given data:-     The modulus of Elasticity, E= 200GPa.

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A:

Q: 1-2-8 The four struts at A, B, C, and D all have the same cross-section. Find the minimum diameter…

A: Given:- Ultimate normal stress=58 ksiFactor of safety=3 To find:- Minimum diameter

Q: A rigid beam ABC supports a linear distributed load with maximum value q while supported by a pin at…

A:

Q: F1-17. The strut is glued to the horizontal member at surface AB. If the strut has a thickness of 25…

A:

Q: A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the…

A: Given Dimeter of wooden stave barrel = 3.5 ft Height of wooden stave barrel = 5 ft Specific gravity…

Q: 8 kN C 2m 1 (3) 15 kN - 2m- -2m-

A:

Q: N A F q C B D X 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed…

A: a = (40+40)/50 = 1.6m  q = (40+25)/20 = 3.25KN/m

Q: H.W No.1: The concrete I-beam of figure is pretensioned with four bounded stranded cables having…

A: Step 1:Step 2:Step 3: Step 4:

Q: A cantilever beam AB of length L = 6.5 ft supportsa trapezoidal distributed load of peak intensity…

A: Given:- L=6.5ft  σallow =18 ksi τallow = 7.5 ksi To find:-  the maximum permissible load q based…

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

A:

Q: 2. Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are…

A: Shear forces acting in parallel with the solid body cause the conversion. As the liquid evaporates,…

Q: 4) Draw the Torsion Diagram for this assembly. A B C D 80 N·m 20 N-m 30 N-m

A: The sign convention for Torsion in shafts follows the right hand thumb rule.Following the right hand…

Q: Question For structure below, complete the missing loading and support data NB: If support A is a…

A: Given data:-

Q: Find the deflection at mid-span of the beam shown. 2kN/m 6m 6m

A: Draw the figure.

Q: Determine the maximum shear stress acting at section a-a of the beam below. 20 mm 4 kN 8 kN 70 mm…

A:

Q: PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the…

A: Calculate the support reactions of the given beam: RA=RB=wL2=5w

Q: The 100-mm diameter shaft is composed of brass (G=34.5 GPa) and steel (G=82.7 GPa) sections rigidly…

A:

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.