F1-17. The strut is glued to the horizontal member at surface AB. If the strut has a thickness of 25 mm and the glue can withstand an average shear stress of 600 kPa, determine the maximum force P that can be applied to the strut. 50 mm A B F1-17 P₁ 60°

Q: The sides of a closed figur

A: Accuracy ratio is the ratio of the error of the measurement to the distance measured. Accuracy…

Q: cos^2 x = cscx cosx/tanx + cotx. prove the identity.

A:

Q: Fastly calculate the value of displacement Work done=20 J force%33 N

A:

Q: Weight of container, Wc 6.35 kg Weight of container with water, Wc+w 20.378| kg Table 3. Unit Weight…

A:

Q: Task 5 a C What is the displacement in place X? a = 0,4 m b = 0,22 m C = 0,25 m. M = 8 kNm E = 210…

A:

Q: Required: Vertical displacement at C PL AE E MB = 0 Fal (6m) – 50kN (2.5m) =0 Fa = 20.83kN %3D Steel…

A:

Q: A flat bar 10 mm thick and 100 mm wide is subjected to a pull of 100 kN. One side of the bar is…

A:

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. If 1 grid…

A:

Q: Find the work done Force 20 N displacement=0.33 m

A: Given Force, F = 20N And displacement, s=0.33m Workdone,W = F*s=20*0.33 = 6.6 Nm Hence Workdone is…

Q: if I want to convert 7 yds^2 to ft^2 shouldnt the answer be 21ft^2? If it is how did I get that…

A: Given:  Area = 7 yds^2 We have to find area in ft^2

Q: Determine the value of Force

A: we know that W = F x S Therefore, F = W/S    = 40/5    = 8N

Q: A 4.020-gram bullet is projected horizontally to a block of timber that rest on a horizontal floor.…

A: Given mass of the bullet  m=4.02 gmbullet is projected horizontallylet the initial speed of the…

Q: why the head loss is not YL= f*L/D* V^2/2g ?

A: Question :why the head loss is not YL= f*L/D* V^2/2g ?

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Step 1: Draw the FBDStep 2: Compute for the normal…

Q: Determine whether the block shown is in equilibrium and find the magnitude and direction of the…

A: Step 1: here we have calculated all the component forces Step 2: here we have calculated the…

Q: 30 m 54 mm 48 mm 54 mm 72 mm A thin, homogeneous wire is bent to form the perimeter of the figure…

A: Wire is bent to form the perimeter of figure aboveCentre of gravity of wire with respect to x,y =?

Q: The equation for the deflected shape of a b follows deflection (0.016x^6 +0.014x^4 +0.01x…

A:

Q: Draw the following shape using autocad 21 20 19 18 17 16 15 14 13 12 11 10 9. 8 7 6 3 1 1 2 3 4 5 6…

A: To Draw the given Drawing using CAD software.

Q: A beam of square cross-section is bent in the plane of its diagonal. A cut is made at top and bottom…

A: A beam of square cross-section is bent in the plane of its diagonal.A cut is made at the top and…

Q: 15 ft diameter ½ inch wall thickness - H?

A:

Q: A beam of square cross-section is bent in the plane of its diagonal. A cut is made at top and bottom…

A: A beam of square cross-section is bent in the plane of its diagonal.A cut is made at the top and…

Q: Find the work done Force=2 N Displacement=1.42 m

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Q: Define e-Log-p Method

A: Pre-consolidation pressure is the maximum lateral pressure that has been experienced by the soil…

Q: Determine the moment of Area of the given Built-up section about its centroidal axis.The top flange…

A: Given I section With top Flange 8" x 1" Bottom flange 16" x 1.5" Stem(web) 16" x 1" 2 Angle sections…

Q: In step 2 how did you solve for maximum elongation? how did you get those values to use?

A: Given: Maximum elongation,  =3+(3×0.25)+(1/2)×0.25=3.875 mm Required : Explain how the above…

Q: The 580-kg uniform beam is sub three external loads shown. Con reactions at the support point O is…

A:

Q: Make an objectives for Fluid Displacement Method for Measuring Volume Solids. Cite your references

A: Measuring the volume of an irregularly shaped object using geometry is often difficult and…

Q: Explain what the differences between finite difference method and finite volume method.

A: Computational fluid dynamics (CFD) is a computer simulation tool for modelling fluid dynamics, that…

Q: Determine the value of force applied if work done is 202 J and value of displacement is 2.5 m

A:

Q: From the figure, determine the number of 4" x 8" x 16" concrete hollow blocks to construct the…

A: Let's take 4 inches thickness of wall  Total volume of fence is L*B*H    L =( 2x53+21+2x5.5 )x39.37…

Q: Three holes are drilled in a plate as shown in the diagram below. Determine dimensions B to two…

A:

Loads and Reactive Forces

Loads are the external influences that a beam experiences under its working conditions. For instance, a beam may be subjected to shear loads, twisting loads, bending moment, and axial loads during its working conditions. Engineers primarily deal with beams and trusses in the civil engineering domain. Due to the influence of loads, it is very crucial to determine the induced stresses and deformation values. These values give an insight into the critical area of the beam that needs to be worked upon to make it fail-safe.