B. Determine the maximum tensile axial force in member DI due to the series of three moving concentrated loads. L 13 m 125KN 100 KN 50 KN -2m-3m-

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A:

Q: Resolve Force in X direction Force=100 N Angle with horizontal is 30 degree

A: Given data-  Force (F) = 100 N  Angle(¢) = 30°

Q: The parameter COD is: O a. Usually less in value than the ulitmate BOD b. Usually equal in value to…

A: The parameter COD is: a. Usually less in value than the ulitmate BODb. Usually equal in value to…

Q: the truss carries forces shown in the figure. determine the resultant of the forces and its…

A: Consider the figure,

Q: Beam One: [Flange = Timber, Web = Timber] The first beam to consider is a fully-timber beam. Note…

A: To find the Depth of Neutral axis, Moment of Inertia and stresses and strains for the Beam One.

Q: Calculate a) reactions b) shear stress c) bending moment diagrams 5 ton E 4 m

A:

Q: Choose the best answer: Classify the structure B A fixed end O Indeterminate to 2nd degree O…

A:

Q: Calculate the stresses that will occur in the pipe for the water pipe buried 5 meters into the…

A: The stress is the dependent parameter and strain is an independent parameter and stress is defined…

Q: a. Positive and negative bending produced in beams, which bending is good in engineering structures.…

A: Solution; As per the given question:

Q: given truss. Pls, indicate the scale. 1000 lb 2000 lb 1000 lb 2000 lb 1000 lb D 1000 lb THE no 2000…

A: given the truss and applied load for the truss

Q: write the advantage and disadvantage of stiffness method and flexibility method

A: Answer The flexibility method is also known as the  Force method. The stiffness method is also known…

Q: Structural mechanics  'method I used was portal method    how do I solve for the following  what…

A: Solution; Using Appropriate method of Analysis

Q: The state of state is given by the following tensor 1 1] [T] 1 1 1 1 11 a- Determine the principal…

A: a) Tensor :               T=111111111 Principal…

Q: Locate the centroid of the composite area below

A:

Q: Required: Vertical displacement at C PL AE E MB = 0 Fal (6m) – 50kN (2.5m) =0 Fa = 20.83kN %3D Steel…

A:

Q: Determine (a) the x, y, and z components of the 750-N force, (b) the angles 0,, 0, and 0, that the…

A: first, draw the vertical and horizontal components Then calculate the scalar components The force…

Q: Plane a-a is called the D.

A:

Q: Give the reason why the shear strain energy in beams can be neglected?

A:

Q: Choose the correct answer Surface tension is :     a. Force/area       d. Energy/length       b. A…

A: Surface tension is a force of attraction in liquids which arises due to the unbalanced cohesive…

Q: Determine the moment of inertia of the shape with respect to the left line

A: The given figure is as follows:

Q: 5 Find the centroid of the following structure. (20 2.5" dia hole- centered 4" 5" 3" 4" 6" 3"

A:

Q: Question 7 7.Value of shear at midspan in Ib. b=3.17 inches h=5.62 inches P= 1657 lb A= 3.75 ft B=…

A: Question is based on the simply supported beam subjected to point load .Magnitude of load and span…

Q: w100 put For Beam #2 shown at left, identify the correct statement(s). a. Mux = 7200. b. VMAx = 1200…

A: For the given simply supported beam having full span WDL of 100lb/ft with a span of 24ft.

Q: w1 kN/m X (x+3) m y W

A: To find resultant force

Q: Provide examples of practical engineering applications of Equation of Elastic Curve

A: we know that,equation of elastic curveM=EId2ydx2where,M= moment EI=flexural rigidity of the beam

Q: Please show all work provided for the following problem so I can understand. Please show step by…

A: Step 1:

Q: F1, F2, and F3 are given as concentrated loads. R is a distributed load equal to 300N/m applied from…

A: Step 1: Step 2: Step 3: solution is given above Step 4:

Q: Effect of temperatures and rate of pulling on ductility value.

A: Ductility test on bitumen is done to test the adhesive property of the bitumen and its ability to…

Q: W. 1. Solve the magnitude of the members BC, BF, and BC. Indicate whether it's compression, tension,…

A: Given : W = 789 Required : Member force in BC and BF

Q: The bending moment diagram of a simply supported beam is shown in figure(a), where AB segment is a…

A: Answer: The answer to the above question is " True". Hence the above statement is True.

Q: The beam has a Young's modulus of Eo =100 GPa, a length of 1 = 4 m and 2nd moment of area of I₂ = 4…

A: Given: E = 100 GPa = 100 x 109 N/m2 Iz = 4 m4 l = 4 m w = 100 N/m

Q: * = pw 2 gm/cm3 1 gm/cm³ O 4 gm/cm³ O 3 gm/cm³ ОООС

A: 1 g/cm3

Q: 2. Determine the moment of area of the given structural built-up section composed of a 8"x1" top…

A: Moment of inertia The moment of inertia, also known as the angular mass or rotational inertia, is a…

Q: prove tañcy) dy

A: Proof of integration ###

Q: In the design of elastomeric bearings, why are steel plates inserted inside the bearings?

A: For elastomeric bearing to function as a soft spring, the bearing should be allowed for bulging…

Q: y = ysecx

A: Given y'= y sec x

Q: Calculate the x-, y-, and z-coordinates of the mass center of the bracket formed from the steel…

A:

Q: Explain the following terms used in GMS. a. IBOUND b. HANI c. RCH d. SY e. SS

A: IBOUNDHANIRCHSYSS

Q: Force Method is also know as Method of Answer Displacement

A: methods of analysis of indeterminate structure is  done by following methods - 1) Force method /…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.